Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add the Zodiac Digital Tapping Unit, a VF610 based network device with
5 Ethernet ports.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds support for the TQ TQMLS1046a board. Currently supported:

- UART
- SD/MMC
- Network on eth3, eth2 currently not working for unknown reasons

First stage support exists but is currently untested. Serdes ports are
not yet supported.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The RDB is the Freescale LS1046a reference board. This patch adds
support for it. Currently supported:

- DDR4 RAM as read from SPD EEPROM
- UART
- SD/MMC
- RGMII network ports

The Serdes ports are currently not supported.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Barebox now has a copy of upstream DTS file for SCU4 AIB board, so
convert corresponding code to use it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for Zodiac's VF610 based SPB4 board.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds initial STMicroelectronics MP1 support along with support
for the DK2 devel board. Only very basic support:

- UART
- SDRAM memory base/size
- No 1st stage support

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The phyCORE-i.MX8M aka PCL-066 is a SoM containing a i.MX8M SoC.

phyCORE-i.MX8M:
 - 1GB LPDDR4 RAM
 - eMMC
 - microSD
 - Ethernet

Signed-off-by: Christian Hemp <christian.hemp@posteo.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Compute Module needs "no-sd" property on the MMC interface otherwise
mci-bcm2835 hangs on SD card probe.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for the following ZII i.MX8MQ based boards:

   - ZII i.MX8MQ RMB3
   - ZII i.MX8MQ Zest

Most of the basic peripherals are supported by this patch. More
advanced features such as PCIe, display support, etc, are planned to
be added later.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Original patch from Uwe Kleine-König, I fixed the
review comments and the imxcfg file to use the udoo neo values.

I also tested the support on the udoo neo full board.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds support for the AM3517 based WAGO pfc200 SPS.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This is a cumulative patch for the Digi ConnectCore CCMX51 SOM.
It includes:
- Switch board to devicetree probe.
- Add MMC update handler.
- Switch to multiimage support.
- Cleanup and optimize board code.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for the Xilinx Zynq Ultrascale+ MPSoC architecture (ZynqMP)
and the Xilinx ZCU104 board.

Barebox is booted as BL33 in EL-1 and expects that a BL2 (i.e. the FSBL)
already took care of initializing the RAM. Also for debug_ll, the UART
is expected to be already setup correctly. Thus, you have to add the
Barebox binary to a boot image as described in "Chapter 11: Boot and
Configuration" of "Zynq Ultrascale+ Device Technical Reference Manual".

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The phyCORE-i.MX 6ULL now comes in a full featured (Y2 variant) and a
low cost (Y0 variant) version. The main difference for the barebox is
the missing second USB OTG port on the Y0 variant and the RAM configuration.

So to account for these differences the existing low cost version is
renamed and the full featured version added.

The results are following phyCORE-i.MX 6ULL modules:

phyCORE-i.MX 6ULL low cost:
	- i.MX 6ULL Y0
	- 256 MB RAM
	- NAND
	- Ethernet 10/100 MBits
	- USB OTG

phyCORE-i.MX 6ULL full featured:
	- i.MX 6ULL Y2
	- 512 MB RAM
	- NAND
	- Ethernet 10/100 MBits
	- USB OTG
	- USB Host

Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

liteboard is a development board which uses liteSOM as its
base. liteSOM can't exist on its own, but is used as part
of other boards - it only contains processor and memory.

Hardware specification:
 * liteSOM:
   - i.MX6UL
   - 256M or 512M DDR3 RAM
   - eMMC (uSDHC2)
 * Ethernet PHY
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds basic support at the same feature level as the other
supported raspberry pi boards.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Roland Hieber <r.hieber@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The EVB-KSZ9477 is an evaluation board for the KSZ9477 ethernet switch.
This board is equipped with a atsama5d3 SoC with 256MiB of SDRAM, 256MiB
of NAND flash and a SD card slot.

For now only second stage booting is supported with AT91bootstrap as
first stage loader.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add ZII SCU3 ESB board, which is i.MX51 based and similar enought to
RDU1 that it can be handled by the same image (different DT).

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add ZII SCU2 Mezz Board. Which is a i.MX51 based board that is similar
enough to RDU1 that they both can be handled by a single
image (type can be detected at runtime).

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>