treewide: remove references to CREDITS ...

The CREDITS file was removed from barebox in 2015 by commit 6570288f2d97
("Remove the CREDITS file"). Remove references to it from several files.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/usb'

usb: Add super speed support ...

This adds the missing bits and pieces to add super speed support to the
USB stack. It is based on the corresponding U-Boot code.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: support set hub depth request for USB 3.0 hubs ...

This is an adoption of U-Boot commit bbc6f06:

| commit bbc6f06
| Author: Bin Meng <bmeng.cn@gmail.com>
| Date:   Wed Jul 19 21:51:13 2017 +0800
|
|     usb: hub: Support 'set hub depth' request for USB 3.0 hubs
|
|     USB 3.0 hub uses a hub depth value multiplied by four as an offset
|     into the 'route string' to locate the bits it uses to determine the
|     downstream port number. We shall set the hub depth value of a USB
|     3.0 hub after it is configured.
|
|     Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|     Reviewed-by: Simon Glass <sjg@chromium.org>

In this patch we also support recording the depth of a hub in
struct usb_device.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: hub: Parse and save TT details from device descriptor ...

Adoption of U-Boot commit 5624dfd:

| commit 5624dfd
| Author: Bin Meng <bmeng.cn@gmail.com>
| Date:   Wed Jul 19 21:51:16 2017 +0800
|
|     usb: hub: Parse and save TT details from device descriptor
|
|     A high speed hub has a special responsibility to handle full speed/
|     low speed devices connected on downstream ports. In this case, the
|     hub must isolate the high speed signaling environment from the full
|     speed/low speed signaling environment with the help of Transaction
|     Translator (TT). TT details are provided by hub descriptors and we
|     parse and save it to hub uclass_priv for later use.
|
|     Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|     Reviewed-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Make driver_info const ...

driver_info shouldn't be changed, make it const.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: rename "struct usb_configuration" to "struct usb_config" ...

struct usb_configuration in usb.h conflicts with struct
usb_configuration in usb/composite.h

The version in usb/composite.h is also defined in Linux, so rename the
other one.

Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Make timeout unit clear ...

The usb_*_msg() functions take a timeout parameter. Make clear which
unit is expected by adding a _ms suffix to the variable name.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Add function to register otg dev ...

We have two drivers in the tree which register an "otg" device to
configure the host/peripheral switching. Before introducing a third
driver create a common function for it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Change power-on / scanning timeout handling ...

Change USB port scanning procedure and timeout handling in the
following ways:

1)
The power-on delay in usb_hub_power_on() is now reduced to a value of
max(100ms, "hub->desc.bPwrOn2PwrGood * 2"). The code does not wait
using mdelay, instead usb_hub_power_on() will wait before querying
the device in the scanning loop later. The total connection timeout for
this hub, which is (1 second + hub->desc.bPwrOn2PwrGood * 2) is
calculated and will be used in the following per-port scanning loop as
the timeout to detect active USB devices on this hub.

2)
Don't delay the minimum delay (for power to stabilize) in
usb_hub_power_on(). Instead skip querying these devices in the scanning
loop usb_scan_port() until the delay time is reached.

3)
The ports are now scanned in a quasi parallel way. The current code did
wait for each (unconnected) port to reach its timeout and only then
continue with the next port. This patch now changes this to scan all
ports of all USB hubs quasi simultaneously. For this, all ports are added
to a scanning list in usb_hub_configure_ports(). The list is later scanned
in usb_device_list_scan() until all ports are ready by either a) reaching
the connection timeout (calculated earlier), or by b) detecting a USB
device. This results in a faster USB scan time as the recursive scanning
of USB hubs connected to the hub that's currently being scanned will
start earlier.

4)
Ports with overcurrent detection will get scanned multiple times if OC
condition is detected (PORT_OVERCURRENT_MAX_SCAN_COUNT).

Without patch:

    $ time usb
    usb: USB: scanning bus for devices...
    usb: 17 USB Device(s) found
    time: 10344ms

With patch:

    $ time usb
    usb: USB: scanning bus for devices...
    usb: 17 USB Device(s) found
    time: 4529ms

Delta: ~6 seconds

Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Drop usb_disable_asynch() ...

There are no users of usb_control_msg() in the codebase that pass
timeout of 0, so it doesn't look like usb_disable_asynch() has any
effect on USB operation. Drop that function and remove all of its uses
to simplify things.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Add usb_unregister_host() ...

We have usb_register_host() which puts a new host on the list
of hosts we should also have the opposite which removes the
host from the list again.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: imx: implement support for limiting host to full speed ...

This is needed when host is known to not work properly in high speed
mode.

In linux, chipidea driver supports 'maximum-speed' device tree property.
When that is set to "full-speed", driver sets PFSC bit in PORTSC
register, which disallows use of high speed mode.

This patch implements same support for barebox.

Important technical detail is that PFSC bit is cleared by port reset,
thus setting it has to be done in ehci->init() callback which is called
after ehci_reset().

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Add usb phy to usb host ...

Add a struct usb_phy * member to struct usb_host. Also, call
usb_phy_notify_connect() / usb_phy_notify_disconnect() when there
are connection changes on the root hub.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: core: return -EAGAIN on usb_* functions reentrance ...

Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: increase USB_CNTL_TIMEOUT to match linux ...

USB requests should be processed within a timeframe of 5s.
The linux kernel also uses this timeout value for the control packets.

For the musb the increase in timeout helps successfully probing USB devices
(at least on one test hardware), but on the other hand doesn't slow down the
system, if there are no devices, i.e. the timeout never hits. That means,
that the USB core correctly aborts instead of timing out.
Why and how the 100ms was chosen in the first place, can not be deduced from
the git history, just that it seems to work fine for most boards.

Change USB_CNTL_TIMEOUT to 5000ms and replace all occurences of
	`USB_CNTL_TIMEOUT * x`
with just
	`USB_CNTL_TIMEOUT`,
as the timeout is now large enough without it.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: abolish wait_ms() function ...

This function is only used in drivers/usb/*.
It is equivalent to mdelay().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: add usb phy header file ...

Mostly taken from the Linux Kernel to ease porting phy
handling code.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: Use descriptors from ch11.h ...

Use the descriptors from ch11.h instead of duplicating them
in usb.h. usb_hub_descriptor now contains a union .u to differentiate
HS hub descriptor from SS hub descriptor.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: host: drop force rescan ...

We can now detect changes in the USB device hierarchy properly, so
the 'force' option to the usb command is no longer necessary. We just
scan the busses each time the usb command is called.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

commands: usb: add tree view capability ...

This patch adds U-Boot 'usb tree' command functionality to barebox.

Here is an example output:

  1 ID 0000:0000
  |  u-boot EHCI Host Controller
  |
  +-2 ID 05e3:0606
    |   USB2.0 Hub
    |
    +-3 ID 10c4:ea60
    |    Silicon Labs CP2102 USB to UART Bridge Contr P-00-00669
    |
    +-4 ID 05e3:0606
    | |   USB2.0 Hub
    | |
    | +-5 ID 05e3:0608
    | | |   USB2.0 Hub
    | | |
    | | +-6 ID 0d8c:000c
    | |       C-Media USB Headphone Set
    | |
    | +-7 ID 0d8c:000c
    |       C-Media USB Headphone Set
    |
    +-8 ID 0846:1040
         NETGEAR NETGEAR FA120 Adapter

The tree view is enabled with 'usb -t'

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: Remove conflicting USB_SPEED_* definitions ...

We have USB_SPEED_* definitions as macros in usb_defs.h and as an enum
in ch9.h. The defines in usb.h correspond to hardware bits in the
ehci controller. Get rid of them and keep the hardware independent
enums.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: Use descriptors from ch9.h ...

Use the descriptors from ch9.h instead of duplicating them
in usb.h

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: introduce usb_interface/usb_configuration structs ...

Currently we have two conflicting definitions of struct usb_config_descriptor
and struct usb_interface_descriptor in the tree. This is because the USB code
uses additional fields in the structs for internal housekeeping. Add
struct usb_interface and struct struct usb_configuration with the housekeeping
data and embed the corresponding hardware structs into them. This frees the
way to use the definitions from ch9.h in the next step.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Documentation: remove doxygen documentation ...

The doxygen documentation is long outdated. Remove it. It will
be replaced with sphinx based documentation later.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: drop unused USB_UHCI_*_ID macros ...

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: remove unimplemented usb_get_dev_index() declaration ...

We do not have usb_get_dev_index() function, so remove this declaration.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: make usb devices children of the corresponding host ...

To be able to find usb devices in the hardware tree.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: implement a usb_host_detect to scan individual USB hosts ...

Currently we can only (re)scan all USB hosts. Add a function to
scan individual hosts. This is useful for implementing the detect
callback in the next patch.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: move scanned status into core ...

A command should not be interested in the internal USB core state, so
move the state handling into the core.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>