/**
 * \file
 *
 * \brief SAM External Interrupt Driver
 *
 * Copyright (C) 2012-2015 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
 */
#include <system.h>
#include <system_interrupt.h>
#include <extint.h>
#include <conf_extint.h>

#if !defined(EXTINT_CLOCK_SOURCE) || defined(__DOXYGEN__)
#  warning  EXTINT_CLOCK_SOURCE is not defined, assuming GCLK_GENERATOR_0.

/** Configuration option, setting the EIC clock source which can be used for
 *  EIC edge detection or filtering. This option may be overridden in the module
 *  configuration header file \c conf_extint.h.
 */
#  define EXTINT_CLOCK_SOURCE GCLK_GENERATOR_0
#endif

/**
 * \internal
 * Internal driver device instance struct.
 */
struct _extint_module _extint_dev;

/**
 * \brief Determin if the general clock is required
 *
 * \param[in] filter_input_signal Filter the raw input signal to prevent noise
 * \param[in] detection_criteria  Edge detection mode to use (\ref extint_detect)
 */
#define _extint_is_gclk_required(filter_input_signal, detection_criteria) \
		((filter_input_signal) ? true : (\
			(EXTINT_DETECT_RISING == (detection_criteria)) ? true : (\
			(EXTINT_DETECT_FALLING == (detection_criteria)) ? true : (\
			(EXTINT_DETECT_BOTH == (detection_criteria)) ? true : false))))

static void _extint_enable(void);
static void _extint_disable(void);

/**
 * \brief Determines if the hardware module(s) are currently synchronizing to the bus.
 *
 * Checks to see if the underlying hardware peripheral module(s) are currently
 * synchronizing across multiple clock domains to the hardware bus, This
 * function can be used to delay further operations on a module until such time
 * that it is ready, to prevent blocking delays for synchronization in the
 * user application.
 *
 * \return Synchronization status of the underlying hardware module(s).
 *
 * \retval true  If the module synchronization is ongoing
 * \retval false If the module has completed synchronization
 */
static inline bool extint_is_syncing(void)
{
    Eic *const eics[EIC_INST_NUM] = EIC_INSTS;

    for (uint32_t i = 0; i < EIC_INST_NUM; i++) {
        if (eics[i]->STATUS.reg & EIC_STATUS_SYNCBUSY) {
            return true;
        }
    }
    return false;
}
/**
 * \internal
 * \brief Initializes and enables the External Interrupt driver.
 *
 * Enable the clocks used by External Interrupt driver.
 *
 * Resets the External Interrupt driver, resetting all hardware
 * module registers to their power-on defaults, then enable it for further use.
 *
 * Reset the callback list if callback mode is used.
 *
 * This function must be called before attempting to use any NMI or standard
 * external interrupt channel functions.
 *
 * \note When SYSTEM module is used, this function will be invoked by
 * \ref system_init() automatically if the module is included.
 */
void _system_extint_init(void);
void _system_extint_init(void)
{
    Eic *const eics[EIC_INST_NUM] = EIC_INSTS;

    /* Turn on the digital interface clock */
    system_apb_clock_set_mask(SYSTEM_CLOCK_APB_APBA, PM_APBAMASK_EIC);

    /* Configure the generic clock for the module and enable it */
    struct system_gclk_chan_config gclk_chan_conf;
    system_gclk_chan_get_config_defaults(&gclk_chan_conf);
    gclk_chan_conf.source_generator = EXTINT_CLOCK_SOURCE;
    system_gclk_chan_set_config(EIC_GCLK_ID, &gclk_chan_conf);

    /* Enable the clock anyway, since when needed it will be requested
     * by External Interrupt driver */
    system_gclk_chan_enable(EIC_GCLK_ID);

    /* Reset all EIC hardware modules. */
    for (uint32_t i = 0; i < EIC_INST_NUM; i++) {
        eics[i]->CTRL.reg |= EIC_CTRL_SWRST;
    }

    while (extint_is_syncing()) {
        /* Wait for all hardware modules to complete synchronization */
    }

    /* Reset the software module */
#if EXTINT_CALLBACK_MODE == true
    /* Clear callback registration table */
    for (uint8_t j = 0; j < EIC_NUMBER_OF_INTERRUPTS; j++) {
        _extint_dev.callbacks[j] = NULL;
    }
    system_interrupt_enable(SYSTEM_INTERRUPT_MODULE_EIC);
#endif

    /* Enables the driver for further use */
    _extint_enable();
}

/**
 * \internal
 * \brief Enables the External Interrupt driver.
 *
 * Enables EIC modules.
 * Registered callback list will not be affected if callback mode is used.
 */
void _extint_enable(void)
{
    Eic *const eics[EIC_INST_NUM] = EIC_INSTS;

    /* Enable all EIC hardware modules. */
    for (uint32_t i = 0; i < EIC_INST_NUM; i++) {
        eics[i]->CTRL.reg |= EIC_CTRL_ENABLE;
    }

    while (extint_is_syncing()) {
        /* Wait for all hardware modules to complete synchronization */
    }
}

/**
 * \internal
 * \brief Disables the External Interrupt driver.
 *
 * Disables EIC modules that were previously started via a call to
 * \ref _extint_enable().
 * Registered callback list will not be affected if callback mode is used.
 */
void _extint_disable(void)
{
    Eic *const eics[EIC_INST_NUM] = EIC_INSTS;

    /* Disable all EIC hardware modules. */
    for (uint32_t i = 0; i < EIC_INST_NUM; i++) {
        eics[i]->CTRL.reg &= ~EIC_CTRL_ENABLE;
    }

    while (extint_is_syncing()) {
        /* Wait for all hardware modules to complete synchronization */
    }
}

/**
 * \brief Initializes an External Interrupt channel configuration structure to defaults.
 *
 * Initializes a given External Interrupt channel configuration structure to a
 * set of known default values. This function should be called on all new
 * instances of these configuration structures before being modified by the
 * user application.
 *
 * The default configuration is as follows:
 * \li Wake the device if an edge detection occurs whilst in sleep
 * \li Input filtering disabled
 * \li Internal pull-up enabled
 * \li Detect falling edges of a signal
 *
 * \param[out] config  Configuration structure to initialize to default values
 */
void extint_chan_get_config_defaults(
    struct extint_chan_conf *const config)
{
    /* Sanity check arguments */
    Assert(config);

    /* Default configuration values */
    config->gpio_pin            = 0;
    config->gpio_pin_mux        = 0;
    config->gpio_pin_pull       = EXTINT_PULL_UP;
    config->wake_if_sleeping    = true;
    config->filter_input_signal = false;
    config->detection_criteria  = EXTINT_DETECT_FALLING;
}

/**
 * \brief Writes an External Interrupt channel configuration to the hardware module.
 *
 * Writes out a given configuration of an External Interrupt channel
 * configuration to the hardware module. If the channel is already configured,
 * the new configuration will replace the existing one.
 *
 * \param[in] channel   External Interrupt channel to configure
 * \param[in] config    Configuration settings for the channel

 */
void extint_chan_set_config(
    const uint8_t channel,
    const struct extint_chan_conf *const config)
{
    /* Sanity check arguments */
    Assert(config);
    /* Sanity check clock requirements */
    Assert(!(!system_gclk_gen_is_enabled(EXTINT_CLOCK_SOURCE) &&
             _extint_is_gclk_required(config->filter_input_signal,
                                      config->detection_criteria)));

    struct system_pinmux_config pinmux_config;
    system_pinmux_get_config_defaults(&pinmux_config);

    pinmux_config.mux_position = config->gpio_pin_mux;
    pinmux_config.direction    = SYSTEM_PINMUX_PIN_DIR_INPUT;
    pinmux_config.input_pull   = (enum system_pinmux_pin_pull)config->gpio_pin_pull;
    system_pinmux_pin_set_config(config->gpio_pin, &pinmux_config);

    /* Get a pointer to the module hardware instance */
    Eic *const EIC_module = _extint_get_eic_from_channel(channel);

    uint32_t config_pos = (4 * (channel % 8));
    uint32_t new_config;

    /* Determine the channel's new edge detection configuration */
    new_config = (config->detection_criteria << EIC_CONFIG_SENSE0_Pos);

    /* Enable the hardware signal filter if requested in the config */
    if (config->filter_input_signal) {
        new_config |= EIC_CONFIG_FILTEN0;
    }

    /* Clear the existing and set the new channel configuration */
    EIC_module->CONFIG[channel / 8].reg
        = (EIC_module->CONFIG[channel / 8].reg &
           ~((EIC_CONFIG_SENSE0_Msk | EIC_CONFIG_FILTEN0) << config_pos)) |
          (new_config << config_pos);

    /* Set the channel's new wake up mode setting */
    if (config->wake_if_sleeping) {
        EIC_module->WAKEUP.reg |=  (1UL << channel);
    } else {
        EIC_module->WAKEUP.reg &= ~(1UL << channel);
    }
}

/**
 * \brief Writes an External Interrupt NMI channel configuration to the hardware module.
 *
 *  Writes out a given configuration of an External Interrupt NMI channel
 *  configuration to the hardware module. If the channel is already configured,
 *  the new configuration will replace the existing one.
 *
 *  \param[in] nmi_channel   External Interrupt NMI channel to configure
 *  \param[in] config        Configuration settings for the channel
 *
 * \returns Status code indicating the success or failure of the request.
 * \retval  STATUS_OK                   Configuration succeeded
 * \retval  STATUS_ERR_PIN_MUX_INVALID  An invalid pinmux value was supplied
 * \retval  STATUS_ERR_BAD_FORMAT       An invalid detection mode was requested
 */
enum status_code extint_nmi_set_config(
    const uint8_t nmi_channel,
    const struct extint_nmi_conf *const config)
{
    /* Sanity check arguments */
    Assert(config);
    /* Sanity check clock requirements */
    Assert(!(!system_gclk_gen_is_enabled(EXTINT_CLOCK_SOURCE) &&
             _extint_is_gclk_required(config->filter_input_signal,
                                      config->detection_criteria)));

    struct system_pinmux_config pinmux_config;
    system_pinmux_get_config_defaults(&pinmux_config);

    pinmux_config.mux_position = config->gpio_pin_mux;
    pinmux_config.direction    = SYSTEM_PINMUX_PIN_DIR_INPUT;
    pinmux_config.input_pull   = SYSTEM_PINMUX_PIN_PULL_UP;
    pinmux_config.input_pull   = (enum system_pinmux_pin_pull)config->gpio_pin_pull;
    system_pinmux_pin_set_config(config->gpio_pin, &pinmux_config);

    /* Get a pointer to the module hardware instance */
    Eic *const EIC_module = _extint_get_eic_from_channel(nmi_channel);

    uint32_t new_config;

    /* Determine the NMI's new edge detection configuration */
    new_config = (config->detection_criteria << EIC_NMICTRL_NMISENSE_Pos);

    /* Enable the hardware signal filter if requested in the config */
    if (config->filter_input_signal) {
        new_config |= EIC_NMICTRL_NMIFILTEN;
    }

    /* Disable EIC and general clock to configure NMI */
    _extint_disable();
    system_gclk_chan_disable(EIC_GCLK_ID);

    EIC_module->NMICTRL.reg = new_config;

    /* Enable the general clock and EIC after configure NMI */
    system_gclk_chan_enable(EIC_GCLK_ID);
    _extint_enable();

    return STATUS_OK;
}

/**
 * \brief Enables an External Interrupt event output.
 *
 *  Enables one or more output events from the External Interrupt module. See
 *  \ref extint_events "here" for a list of events this module supports.
 *
 *  \note Events cannot be altered while the module is enabled.
 *
 *  \param[in] events    Struct containing flags of events to enable
 */
void extint_enable_events(
    struct extint_events *const events)
{
    /* Sanity check arguments */
    Assert(events);

    /* Array of available EICs. */
    Eic *const eics[EIC_INST_NUM] = EIC_INSTS;

    /* Update the event control register for each physical EIC instance */
    for (uint32_t i = 0; i < EIC_INST_NUM; i++) {
        uint32_t event_mask = 0;

        /* Create an enable mask for the current EIC module */
        for (uint32_t j = 0; j < 32; j++) {
            if (events->generate_event_on_detect[(32 * i) + j]) {
                event_mask |= (1UL << j);
            }
        }

        /* Enable the masked events */
        eics[i]->EVCTRL.reg |= event_mask;
    }
}

/**
 * \brief Disables an External Interrupt event output.
 *
 *  Disables one or more output events from the External Interrupt module. See
 *  \ref extint_events "here" for a list of events this module supports.
 *
 *  \note Events cannot be altered while the module is enabled.
 *
 *  \param[in] events    Struct containing flags of events to disable
 */
void extint_disable_events(
    struct extint_events *const events)
{
    /* Sanity check arguments */
    Assert(events);

    /* Array of available EICs. */
    Eic *const eics[EIC_INST_NUM] = EIC_INSTS;

    /* Update the event control register for each physical EIC instance */
    for (uint32_t i = 0; i < EIC_INST_NUM; i++) {
        uint32_t event_mask = 0;

        /* Create a disable mask for the current EIC module */
        for (uint32_t j = 0; j < 32; j++) {
            if (events->generate_event_on_detect[(32 * i) + j]) {
                event_mask |= (1UL << j);
            }
        }

        /* Disable the masked events */
        eics[i]->EVCTRL.reg &= ~event_mask;
    }
}