/* mbed Microcontroller Library
* Copyright (c) 2018-2018 ARM Limited
* SPDX-License-Identifier: Apache-2.0
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
#ifndef MBED_QSPI_FLASH_MX25L51245G_H
#define MBED_QSPI_FLASH_MX25L51245G_H
#define QSPI_FLASH_CHIP_STRING "macronix MX25L51245G"
// Command for reading status register
#define QSPI_CMD_RDSR 0x05
// Command for reading configuration register
#define QSPI_CMD_RDCR0 0x15
// Command for writing status/configuration register
#define QSPI_CMD_WRSR 0x01
// Command for reading security register
#define QSPI_CMD_RDSCUR 0x2B
// Command for setting Reset Enable
#define QSPI_CMD_RSTEN 0x66
// Command for setting Reset
#define QSPI_CMD_RST 0x99
// Command for setting write enable
#define QSPI_CMD_WREN 0x06
// Command for setting write disable
#define QSPI_CMD_WRDI 0x04
// WRSR operations max time [us] (datasheet max time + 15%)
#define QSPI_WRSR_MAX_TIME 34500 // 30ms
// general wait max time [us]
#define QSPI_WAIT_MAX_TIME 100000 // 100ms
// Commands for writing (page programming)
#define QSPI_CMD_WRITE_1IO 0x02 // 1-1-1 mode
#define QSPI_CMD_WRITE_4IO 0x38 // 1-4-4 mode
// write operations max time [us] (datasheet max time + 15%)
#define QSPI_PAGE_PROG_MAX_TIME 11500 // 10ms
#define QSPI_PAGE_SIZE 256 // 256B
#define QSPI_SECTOR_SIZE 4096 // 4kB
#define QSPI_SECTOR_COUNT 2048 //
// Commands for reading
#define QSPI_CMD_READ_1IO_FAST 0x0B // 1-1-1 mode
#define QSPI_CMD_READ_1IO 0x03 // 1-1-1 mode
#define QSPI_CMD_READ_2IO 0xBB // 1-2-2 mode
#define QSPI_CMD_READ_1I2O 0x3B // 1-1-2 mode
#define QSPI_CMD_READ_4IO 0xEB // 1-4-4 mode
#define QSPI_CMD_READ_1I4O 0x6B // 1-1-4 mode
#define QSPI_READ_1IO_DUMMY_CYCLE 0
#define QSPI_READ_FAST_DUMMY_CYCLE 8
#define QSPI_READ_2IO_DUMMY_CYCLE 4
#define QSPI_READ_1I2O_DUMMY_CYCLE 8
#define QSPI_READ_4IO_DUMMY_CYCLE 6
#define QSPI_READ_1I4O_DUMMY_CYCLE 8
// Commands for erasing
#define QSPI_CMD_ERASE_SECTOR 0x20 // 4kB
#define QSPI_CMD_ERASE_BLOCK_32 0x52 // 32kB
#define QSPI_CMD_ERASE_BLOCK_64 0xD8 // 64kB
#define QSPI_CMD_ERASE_CHIP 0x60 // or 0xC7
// erase operations max time [us] (datasheet max time + 15%)
#define QSPI_ERASE_SECTOR_MAX_TIME 480000 // 400 ms
#define QSPI_ERASE_BLOCK_32_MAX_TIME 1200000 // 1s
#define QSPI_ERASE_BLOCK_64_MAX_TIME 2400000 // 2s
// max frequency for basic rw operation (for fast mode)
#define QSPI_COMMON_MAX_FREQUENCY 32000000
#define QSPI_STATUS_REG_SIZE 1
#define QSPI_CONFIG_REG_0_SIZE 2
#define QSPI_SECURITY_REG_SIZE 1
#define QSPI_MAX_REG_SIZE 2
// status register
#define STATUS_BIT_WIP (1 << 0) // write in progress bit
#define STATUS_BIT_WEL (1 << 1) // write enable latch
#define STATUS_BIT_BP0 (1 << 2) //
#define STATUS_BIT_BP1 (1 << 3) //
#define STATUS_BIT_BP2 (1 << 4) //
#define STATUS_BIT_BP3 (1 << 5) //
#define STATUS_BIT_QE (1 << 6) // Quad Enable
#define STATUS_BIT_SRWD (1 << 7) // status register write protect
// configuration register 0
// bit 0, 1, 2, 4, 5, 7 reserved
#define CONFIG0_BIT_TB (1 << 3) // Top/Bottom area protect
#endif // MBED_QSPI_FLASH_MX25L51245G_H
