GitBucket
Newer
/**
******************************************************************************
* @file stm32l1xx_hal_irda.h
* @author MCD Application Team
* @brief Header file of IRDA HAL module.
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32L1xx_HAL_IRDA_H
#define __STM32L1xx_HAL_IRDA_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32l1xx_hal_def.h"
/** @addtogroup STM32L1xx_HAL_Driver
* @{
*/
/** @addtogroup IRDA
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup IRDA_Exported_Types IRDA Exported Types
* @{
*/
/**
* @brief IRDA Init Structure definition
*/
typedef struct
{
uint32_t BaudRate; /*!< This member configures the IRDA communication baud rate.
The baud rate is computed using the following formula:
- IntegerDivider = ((PCLKx) / (16 * (hirda->Init.BaudRate)))
- FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 16) + 0.5 */
uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
This parameter can be a value of @ref IRDA_Word_Length */
uint32_t Parity; /*!< Specifies the parity mode.
This parameter can be a value of @ref IRDA_Parity
@note When parity is enabled, the computed parity is inserted
at the MSB position of the transmitted data (9th bit when
the word length is set to 9 data bits; 8th bit when the
word length is set to 8 data bits). */
uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
This parameter can be a value of @ref IRDA_Mode */
uint8_t Prescaler; /*!< Specifies the Prescaler value to be programmed
in the IrDA low-power Baud Register, for defining pulse width on which
burst acceptance/rejection will be decided. This value is used as divisor
of system clock to achieve required pulse width. */
uint32_t IrDAMode; /*!< Specifies the IrDA mode
This parameter can be a value of @ref IRDA_Low_Power */
} IRDA_InitTypeDef;
/**
* @brief HAL IRDA State structures definition
* @note HAL IRDA State value is a combination of 2 different substates: gState and RxState.
* - gState contains IRDA state information related to global Handle management
* and also information related to Tx operations.
* gState value coding follow below described bitmap :
* b7-b6 Error information
* 00 : No Error
* 01 : (Not Used)
* 10 : Timeout
* 11 : Error
* b5 IP initilisation status
* 0 : Reset (IP not initialized)
* 1 : Init done (IP not initialized. HAL IRDA Init function already called)
* b4-b3 (not used)
* xx : Should be set to 00
* b2 Intrinsic process state
* 0 : Ready
* 1 : Busy (IP busy with some configuration or internal operations)
* b1 (not used)
* x : Should be set to 0
* b0 Tx state
* 0 : Ready (no Tx operation ongoing)
* 1 : Busy (Tx operation ongoing)
* - RxState contains information related to Rx operations.
* RxState value coding follow below described bitmap :
* b7-b6 (not used)
* xx : Should be set to 00
* b5 IP initilisation status
* 0 : Reset (IP not initialized)
* 1 : Init done (IP not initialized)
* b4-b2 (not used)
* xxx : Should be set to 000
* b1 Rx state
* 0 : Ready (no Rx operation ongoing)
* 1 : Busy (Rx operation ongoing)
* b0 (not used)
* x : Should be set to 0.
*/
typedef enum
{
HAL_IRDA_STATE_RESET = 0x00U, /*!< Peripheral is not yet Initialized
Value is allowed for gState and RxState */
HAL_IRDA_STATE_READY = 0x20U, /*!< Peripheral Initialized and ready for use
Value is allowed for gState and RxState */
HAL_IRDA_STATE_BUSY = 0x24U, /*!< An internal process is ongoing
Value is allowed for gState only */
HAL_IRDA_STATE_BUSY_TX = 0x21U, /*!< Data Transmission process is ongoing
Value is allowed for gState only */
HAL_IRDA_STATE_BUSY_RX = 0x22U, /*!< Data Reception process is ongoing
Value is allowed for RxState only */
HAL_IRDA_STATE_BUSY_TX_RX = 0x23U, /*!< Data Transmission and Reception process is ongoing
Not to be used for neither gState nor RxState.
Value is result of combination (Or) between gState and RxState values */
HAL_IRDA_STATE_TIMEOUT = 0xA0U, /*!< Timeout state
Value is allowed for gState only */
HAL_IRDA_STATE_ERROR = 0xE0U /*!< Error
Value is allowed for gState only */
} HAL_IRDA_StateTypeDef;
/**
* @brief IRDA handle Structure definition
*/
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
typedef struct __IRDA_HandleTypeDef
#else
typedef struct
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
{
USART_TypeDef *Instance; /*!< USART registers base address */
IRDA_InitTypeDef Init; /*!< IRDA communication parameters */
uint8_t *pTxBuffPtr; /*!< Pointer to IRDA Tx transfer Buffer */
uint16_t TxXferSize; /*!< IRDA Tx Transfer size */
__IO uint16_t TxXferCount; /*!< IRDA Tx Transfer Counter */
uint8_t *pRxBuffPtr; /*!< Pointer to IRDA Rx transfer Buffer */
uint16_t RxXferSize; /*!< IRDA Rx Transfer size */
__IO uint16_t RxXferCount; /*!< IRDA Rx Transfer Counter */
DMA_HandleTypeDef *hdmatx; /*!< IRDA Tx DMA Handle parameters */
DMA_HandleTypeDef *hdmarx; /*!< IRDA Rx DMA Handle parameters */
HAL_LockTypeDef Lock; /*!< Locking object */
__IO HAL_IRDA_StateTypeDef gState; /*!< IRDA state information related to global Handle management
and also related to Tx operations.
This parameter can be a value of @ref HAL_IRDA_StateTypeDef */
__IO HAL_IRDA_StateTypeDef RxState; /*!< IRDA state information related to Rx operations.
This parameter can be a value of @ref HAL_IRDA_StateTypeDef */
__IO uint32_t ErrorCode; /*!< IRDA Error code */
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
void (* TxHalfCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Tx Half Complete Callback */
void (* TxCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Tx Complete Callback */
void (* RxHalfCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Rx Half Complete Callback */
void (* RxCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Rx Complete Callback */
void (* ErrorCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Error Callback */
void (* AbortCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Abort Complete Callback */
void (* AbortTransmitCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Abort Transmit Complete Callback */
void (* AbortReceiveCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Abort Receive Complete Callback */
void (* MspInitCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Msp Init callback */
void (* MspDeInitCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Msp DeInit callback */
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
} IRDA_HandleTypeDef;
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
/**
* @brief HAL IRDA Callback ID enumeration definition
*/
typedef enum
{
HAL_IRDA_TX_HALFCOMPLETE_CB_ID = 0x00U, /*!< IRDA Tx Half Complete Callback ID */
HAL_IRDA_TX_COMPLETE_CB_ID = 0x01U, /*!< IRDA Tx Complete Callback ID */
HAL_IRDA_RX_HALFCOMPLETE_CB_ID = 0x02U, /*!< IRDA Rx Half Complete Callback ID */
HAL_IRDA_RX_COMPLETE_CB_ID = 0x03U, /*!< IRDA Rx Complete Callback ID */
HAL_IRDA_ERROR_CB_ID = 0x04U, /*!< IRDA Error Callback ID */
HAL_IRDA_ABORT_COMPLETE_CB_ID = 0x05U, /*!< IRDA Abort Complete Callback ID */
HAL_IRDA_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x06U, /*!< IRDA Abort Transmit Complete Callback ID */
HAL_IRDA_ABORT_RECEIVE_COMPLETE_CB_ID = 0x07U, /*!< IRDA Abort Receive Complete Callback ID */
HAL_IRDA_MSPINIT_CB_ID = 0x08U, /*!< IRDA MspInit callback ID */
HAL_IRDA_MSPDEINIT_CB_ID = 0x09U /*!< IRDA MspDeInit callback ID */
} HAL_IRDA_CallbackIDTypeDef;
/**
* @brief HAL IRDA Callback pointer definition
*/
typedef void (*pIRDA_CallbackTypeDef)(IRDA_HandleTypeDef *hirda); /*!< pointer to an IRDA callback function */
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup IRDA_Exported_Constants IRDA Exported constants
* @{
*/
/** @defgroup IRDA_Error_Code IRDA Error Code
* @{
*/
#define HAL_IRDA_ERROR_NONE 0x00000000U /*!< No error */
#define HAL_IRDA_ERROR_PE 0x00000001U /*!< Parity error */
#define HAL_IRDA_ERROR_NE 0x00000002U /*!< Noise error */
#define HAL_IRDA_ERROR_FE 0x00000004U /*!< Frame error */
#define HAL_IRDA_ERROR_ORE 0x00000008U /*!< Overrun error */
#define HAL_IRDA_ERROR_DMA 0x00000010U /*!< DMA transfer error */
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
#define HAL_IRDA_ERROR_INVALID_CALLBACK ((uint32_t)0x00000020U) /*!< Invalid Callback error */
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
/**
* @}
*/
/** @defgroup IRDA_Word_Length IRDA Word Length
* @{
*/
#define IRDA_WORDLENGTH_8B 0x00000000U
#define IRDA_WORDLENGTH_9B ((uint32_t)USART_CR1_M)
/**
* @}
*/
/** @defgroup IRDA_Parity IRDA Parity
* @{
*/
#define IRDA_PARITY_NONE 0x00000000U
#define IRDA_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
#define IRDA_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
/**
* @}
*/
/** @defgroup IRDA_Mode IRDA Transfer Mode
* @{
*/
#define IRDA_MODE_RX ((uint32_t)USART_CR1_RE)
#define IRDA_MODE_TX ((uint32_t)USART_CR1_TE)
#define IRDA_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
/**
* @}
*/
/** @defgroup IRDA_Low_Power IRDA Low Power
* @{
*/
#define IRDA_POWERMODE_LOWPOWER ((uint32_t)USART_CR3_IRLP)
#define IRDA_POWERMODE_NORMAL 0x00000000U
/**
* @}
*/
/** @defgroup IRDA_Flags IRDA Flags
* Elements values convention: 0xXXXX
* - 0xXXXX : Flag mask in the SR register
* @{
*/
#define IRDA_FLAG_TXE ((uint32_t)USART_SR_TXE)
#define IRDA_FLAG_TC ((uint32_t)USART_SR_TC)
#define IRDA_FLAG_RXNE ((uint32_t)USART_SR_RXNE)
#define IRDA_FLAG_IDLE ((uint32_t)USART_SR_IDLE)
#define IRDA_FLAG_ORE ((uint32_t)USART_SR_ORE)
#define IRDA_FLAG_NE ((uint32_t)USART_SR_NE)
#define IRDA_FLAG_FE ((uint32_t)USART_SR_FE)
#define IRDA_FLAG_PE ((uint32_t)USART_SR_PE)
/**
* @}
*/
/** @defgroup IRDA_Interrupt_definition IRDA Interrupt Definitions
* Elements values convention: 0xY000XXXX
* - XXXX : Interrupt mask in the XX register
* - Y : Interrupt source register (2bits)
* - 01: CR1 register
* - 10: CR2 register
* - 11: CR3 register
* @{
*/
#define IRDA_IT_PE ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_PEIE))
#define IRDA_IT_TXE ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_TXEIE))
#define IRDA_IT_TC ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_TCIE))
#define IRDA_IT_RXNE ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE))
#define IRDA_IT_IDLE ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE))
#define IRDA_IT_LBD ((uint32_t)(IRDA_CR2_REG_INDEX << 28U | USART_CR2_LBDIE))
#define IRDA_IT_CTS ((uint32_t)(IRDA_CR3_REG_INDEX << 28U | USART_CR3_CTSIE))
#define IRDA_IT_ERR ((uint32_t)(IRDA_CR3_REG_INDEX << 28U | USART_CR3_EIE))
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup IRDA_Exported_Macros IRDA Exported Macros
* @{
*/
/** @brief Reset IRDA handle gstate & RxState
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#if USE_HAL_IRDA_REGISTER_CALLBACKS == 1
#define __HAL_IRDA_RESET_HANDLE_STATE(__HANDLE__) do{ \
(__HANDLE__)->gState = HAL_IRDA_STATE_RESET; \
(__HANDLE__)->RxState = HAL_IRDA_STATE_RESET; \
(__HANDLE__)->MspInitCallback = NULL; \
(__HANDLE__)->MspDeInitCallback = NULL; \
} while(0U)
#else
#define __HAL_IRDA_RESET_HANDLE_STATE(__HANDLE__) do{ \
(__HANDLE__)->gState = HAL_IRDA_STATE_RESET; \
(__HANDLE__)->RxState = HAL_IRDA_STATE_RESET; \
} while(0U)
#endif /*USE_HAL_IRDA_REGISTER_CALLBACKS */
/** @brief Flush the IRDA DR register
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR)
/** @brief Check whether the specified IRDA flag is set or not.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @param __FLAG__ specifies the flag to check.
* This parameter can be one of the following values:
* @arg IRDA_FLAG_TXE: Transmit data register empty flag
* @arg IRDA_FLAG_TC: Transmission Complete flag
* @arg IRDA_FLAG_RXNE: Receive data register not empty flag
* @arg IRDA_FLAG_IDLE: Idle Line detection flag
* @arg IRDA_FLAG_ORE: OverRun Error flag
* @arg IRDA_FLAG_NE: Noise Error flag
* @arg IRDA_FLAG_FE: Framing Error flag
* @arg IRDA_FLAG_PE: Parity Error flag
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_IRDA_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
/** @brief Clear the specified IRDA pending flag.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @param __FLAG__ specifies the flag to check.
* This parameter can be any combination of the following values:
* @arg IRDA_FLAG_TC: Transmission Complete flag.
* @arg IRDA_FLAG_RXNE: Receive data register not empty flag.
*
* @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
* error) and IDLE (Idle line detected) flags are cleared by software
* sequence: a read operation to USART_SR register followed by a read
* operation to USART_DR register.
* @note RXNE flag can be also cleared by a read to the USART_DR register.
* @note TC flag can be also cleared by software sequence: a read operation to
* USART_SR register followed by a write operation to USART_DR register.
* @note TXE flag is cleared only by a write to the USART_DR register.
* @retval None
*/
#define __HAL_IRDA_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
/** @brief Clear the IRDA PE pending flag.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__) \
do{ \
__IO uint32_t tmpreg = 0x00U; \
tmpreg = (__HANDLE__)->Instance->SR; \
tmpreg = (__HANDLE__)->Instance->DR; \
UNUSED(tmpreg); \
} while(0U)
/** @brief Clear the IRDA FE pending flag.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_CLEAR_FEFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
/** @brief Clear the IRDA NE pending flag.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_CLEAR_NEFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
/** @brief Clear the IRDA ORE pending flag.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_CLEAR_OREFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
/** @brief Clear the IRDA IDLE pending flag.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_CLEAR_IDLEFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
/** @brief Enable the specified IRDA interrupt.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @param __INTERRUPT__ specifies the IRDA interrupt source to enable.
* This parameter can be one of the following values:
* @arg IRDA_IT_TXE: Transmit Data Register empty interrupt
* @arg IRDA_IT_TC: Transmission complete interrupt
* @arg IRDA_IT_RXNE: Receive Data register not empty interrupt
* @arg IRDA_IT_IDLE: Idle line detection interrupt
* @arg IRDA_IT_PE: Parity Error interrupt
* @arg IRDA_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_IRDA_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28U) == IRDA_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & IRDA_IT_MASK)): \
(((__INTERRUPT__) >> 28U) == IRDA_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & IRDA_IT_MASK)): \
((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & IRDA_IT_MASK)))
/** @brief Disable the specified IRDA interrupt.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @param __INTERRUPT__ specifies the IRDA interrupt source to disable.
* This parameter can be one of the following values:
* @arg IRDA_IT_TXE: Transmit Data Register empty interrupt
* @arg IRDA_IT_TC: Transmission complete interrupt
* @arg IRDA_IT_RXNE: Receive Data register not empty interrupt
* @arg IRDA_IT_IDLE: Idle line detection interrupt
* @arg IRDA_IT_PE: Parity Error interrupt
* @arg IRDA_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_IRDA_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28U) == IRDA_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & IRDA_IT_MASK)): \
(((__INTERRUPT__) >> 28U) == IRDA_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & IRDA_IT_MASK)): \
((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & IRDA_IT_MASK)))
/** @brief Check whether the specified IRDA interrupt has occurred or not.
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @param __IT__ specifies the IRDA interrupt source to check.
* This parameter can be one of the following values:
* @arg IRDA_IT_TXE: Transmit Data Register empty interrupt
* @arg IRDA_IT_TC: Transmission complete interrupt
* @arg IRDA_IT_RXNE: Receive Data register not empty interrupt
* @arg IRDA_IT_IDLE: Idle line detection interrupt
* @arg IRDA_IT_ERR: Error interrupt
* @arg IRDA_IT_PE: Parity Error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_IRDA_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == IRDA_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28U) == IRDA_CR2_REG_INDEX)? \
(__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & IRDA_IT_MASK))
/** @brief Macro to enable the IRDA's one bit sample method
* @param __HANDLE__ specifies the IRDA Handle.
* @retval None
*/
#define __HAL_IRDA_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 |= USART_CR3_ONEBIT)
/** @brief Macro to disable the IRDA's one bit sample method
* @param __HANDLE__ specifies the IRDA Handle.
* @retval None
*/
#define __HAL_IRDA_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
/** @brief Enable UART/USART associated to IRDA Handle
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_ENABLE(__HANDLE__) (SET_BIT((__HANDLE__)->Instance->CR1, USART_CR1_UE))
/** @brief Disable UART/USART associated to IRDA Handle
* @param __HANDLE__ specifies the IRDA Handle.
* IRDA Handle selects the USARTx or UARTy peripheral
* (USART,UART availability and x,y values depending on device).
* @retval None
*/
#define __HAL_IRDA_DISABLE(__HANDLE__) (CLEAR_BIT((__HANDLE__)->Instance->CR1, USART_CR1_UE))
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup IRDA_Exported_Functions
* @{
*/
/** @addtogroup IRDA_Exported_Functions_Group1
* @{
*/
/* Initialization/de-initialization functions **********************************/
HAL_StatusTypeDef HAL_IRDA_Init(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_DeInit(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_MspInit(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_MspDeInit(IRDA_HandleTypeDef *hirda);
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
/* Callbacks Register/UnRegister functions ***********************************/
HAL_StatusTypeDef HAL_IRDA_RegisterCallback(IRDA_HandleTypeDef *hirda, HAL_IRDA_CallbackIDTypeDef CallbackID, pIRDA_CallbackTypeDef pCallback);
HAL_StatusTypeDef HAL_IRDA_UnRegisterCallback(IRDA_HandleTypeDef *hirda, HAL_IRDA_CallbackIDTypeDef CallbackID);
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
/**
* @}
*/
/** @addtogroup IRDA_Exported_Functions_Group2
* @{
*/
/* IO operation functions *******************************************************/
HAL_StatusTypeDef HAL_IRDA_Transmit(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_IRDA_Receive(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_Receive_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_Transmit_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_Receive_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_DMAPause(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_DMAResume(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_DMAStop(IRDA_HandleTypeDef *hirda);
/* Transfer Abort functions */
HAL_StatusTypeDef HAL_IRDA_Abort(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortTransmit(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortReceive(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_Abort_IT(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortTransmit_IT(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortReceive_IT(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_IRQHandler(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_TxCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_RxCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_TxHalfCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_RxHalfCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_ErrorCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_AbortCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_AbortTransmitCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_AbortReceiveCpltCallback(IRDA_HandleTypeDef *hirda);
/**
* @}
*/
/** @addtogroup IRDA_Exported_Functions_Group3
* @{
*/
/* Peripheral State functions **************************************************/
HAL_IRDA_StateTypeDef HAL_IRDA_GetState(IRDA_HandleTypeDef *hirda);
uint32_t HAL_IRDA_GetError(IRDA_HandleTypeDef *hirda);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup IRDA_Private_Constants IRDA Private Constants
* @{
*/
/** @brief IRDA interruptions flag mask
*
*/
#define IRDA_IT_MASK ((uint32_t) USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | \
USART_CR1_IDLEIE | USART_CR2_LBDIE | USART_CR3_CTSIE | USART_CR3_EIE )
#define IRDA_CR1_REG_INDEX 1U
#define IRDA_CR2_REG_INDEX 2U
#define IRDA_CR3_REG_INDEX 3U
/**
* @}
*/
/* Private macros --------------------------------------------------------*/
/** @defgroup IRDA_Private_Macros IRDA Private Macros
* @{
*/
#define IS_IRDA_WORD_LENGTH(LENGTH) (((LENGTH) == IRDA_WORDLENGTH_8B) || \
((LENGTH) == IRDA_WORDLENGTH_9B))
#define IS_IRDA_PARITY(PARITY) (((PARITY) == IRDA_PARITY_NONE) || \
((PARITY) == IRDA_PARITY_EVEN) || \
((PARITY) == IRDA_PARITY_ODD))
#define IS_IRDA_MODE(MODE) ((((MODE) & 0x0000FFF3U) == 0x00U) && ((MODE) != 0x00000000U))
#define IS_IRDA_POWERMODE(MODE) (((MODE) == IRDA_POWERMODE_LOWPOWER) || \
((MODE) == IRDA_POWERMODE_NORMAL))
#define IS_IRDA_BAUDRATE(BAUDRATE) ((BAUDRATE) < 115201U)
#define IRDA_DIV(_PCLK_, _BAUD_) (((_PCLK_)*25U)/(4U*(_BAUD_)))
#define IRDA_DIVMANT(_PCLK_, _BAUD_) (IRDA_DIV((_PCLK_), (_BAUD_))/100U)
#define IRDA_DIVFRAQ(_PCLK_, _BAUD_) ((((IRDA_DIV((_PCLK_), (_BAUD_)) - (IRDA_DIVMANT((_PCLK_), (_BAUD_)) * 100U)) * 16U) + 50U) / 100U)
/* UART BRR = mantissa + overflow + fraction
= (UART DIVMANT << 4) + (UART DIVFRAQ & 0xF0) + (UART DIVFRAQ & 0x0FU) */
#define IRDA_BRR(_PCLK_, _BAUD_) (((IRDA_DIVMANT((_PCLK_), (_BAUD_)) << 4U) + \
(IRDA_DIVFRAQ((_PCLK_), (_BAUD_)) & 0xF0U)) + \
(IRDA_DIVFRAQ((_PCLK_), (_BAUD_)) & 0x0FU))
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup IRDA_Private_Functions IRDA Private Functions
* @{
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32L1xx_HAL_IRDA_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/