GitBucket
Newer
/**
******************************************************************************
* @file stm32l4xx_hal_flash_ex.c
* @author MCD Application Team
* @brief Extended FLASH HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the FLASH extended peripheral:
* + Extended programming operations functions
*
@verbatim
==============================================================================
##### Flash Extended features #####
==============================================================================
[..] Comparing to other previous devices, the FLASH interface for STM32L4xx
devices contains the following additional features
(+) Capacity up to 2 Mbyte with dual bank architecture supporting read-while-write
capability (RWW)
(+) Dual bank memory organization
(+) PCROP protection for all banks
##### How to use this driver #####
==============================================================================
[..] This driver provides functions to configure and program the FLASH memory
of all STM32L4xx devices. It includes
(#) Flash Memory Erase functions:
(++) Lock and Unlock the FLASH interface using HAL_FLASH_Unlock() and
HAL_FLASH_Lock() functions
(++) Erase function: Erase page, erase all sectors
(++) There are two modes of erase :
(+++) Polling Mode using HAL_FLASHEx_Erase()
(+++) Interrupt Mode using HAL_FLASHEx_Erase_IT()
(#) Option Bytes Programming function: Use HAL_FLASHEx_OBProgram() to :
(++) Set/Reset the write protection
(++) Set the Read protection Level
(++) Program the user Option Bytes
(++) Configure the PCROP protection
(#) Get Option Bytes Configuration function: Use HAL_FLASHEx_OBGetConfig() to :
(++) Get the value of a write protection area
(++) Know if the read protection is activated
(++) Get the value of the user Option Bytes
(++) Get the value of a PCROP area
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2017 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32l4xx_hal.h"
/** @addtogroup STM32L4xx_HAL_Driver
* @{
*/
/** @defgroup FLASHEx FLASHEx
* @brief FLASH Extended HAL module driver
* @{
*/
#ifdef HAL_FLASH_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/** @defgroup FLASHEx_Private_Functions FLASHEx Private Functions
* @{
*/
static void FLASH_MassErase(uint32_t Banks);
static HAL_StatusTypeDef FLASH_OB_WRPConfig(uint32_t WRPArea, uint32_t WRPStartOffset, uint32_t WRDPEndOffset);
static HAL_StatusTypeDef FLASH_OB_RDPConfig(uint32_t RDPLevel);
static HAL_StatusTypeDef FLASH_OB_UserConfig(uint32_t UserType, uint32_t UserConfig);
static HAL_StatusTypeDef FLASH_OB_PCROPConfig(uint32_t PCROPConfig, uint32_t PCROPStartAddr, uint32_t PCROPEndAddr);
static void FLASH_OB_GetWRP(uint32_t WRPArea, uint32_t * WRPStartOffset, uint32_t * WRDPEndOffset);
static uint32_t FLASH_OB_GetRDP(void);
static uint32_t FLASH_OB_GetUser(void);
static void FLASH_OB_GetPCROP(uint32_t * PCROPConfig, uint32_t * PCROPStartAddr, uint32_t * PCROPEndAddr);
/**
* @}
*/
/* Exported functions -------------------------------------------------------*/
/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions
* @{
*/
/** @defgroup FLASHEx_Exported_Functions_Group1 Extended IO operation functions
* @brief Extended IO operation functions
*
@verbatim
===============================================================================
##### Extended programming operation functions #####
===============================================================================
[..]
This subsection provides a set of functions allowing to manage the Extended FLASH
programming operations Operations.
@endverbatim
* @{
*/
/**
* @brief Perform a mass erase or erase the specified FLASH memory pages.
* @param[in] pEraseInit: pointer to an FLASH_EraseInitTypeDef structure that
* contains the configuration information for the erasing.
*
* @param[out] PageError : pointer to variable that contains the configuration
* information on faulty page in case of error (0xFFFFFFFF means that all
* the pages have been correctly erased)
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *PageError)
{
HAL_StatusTypeDef status;
uint32_t page_index;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if (status == HAL_OK)
{
pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
/* Deactivate the cache if they are activated to avoid data misbehavior */
if(READ_BIT(FLASH->ACR, FLASH_ACR_ICEN) != 0U)
{
/* Disable instruction cache */
__HAL_FLASH_INSTRUCTION_CACHE_DISABLE();
if(READ_BIT(FLASH->ACR, FLASH_ACR_DCEN) != 0U)
{
/* Disable data cache */
__HAL_FLASH_DATA_CACHE_DISABLE();
pFlash.CacheToReactivate = FLASH_CACHE_ICACHE_DCACHE_ENABLED;
}
else
{
pFlash.CacheToReactivate = FLASH_CACHE_ICACHE_ENABLED;
}
}
else if(READ_BIT(FLASH->ACR, FLASH_ACR_DCEN) != 0U)
{
/* Disable data cache */
__HAL_FLASH_DATA_CACHE_DISABLE();
pFlash.CacheToReactivate = FLASH_CACHE_DCACHE_ENABLED;
}
else
{
pFlash.CacheToReactivate = FLASH_CACHE_DISABLED;
}
if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
{
/* Mass erase to be done */
FLASH_MassErase(pEraseInit->Banks);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
/* If the erase operation is completed, disable the MER1 and MER2 Bits */
CLEAR_BIT(FLASH->CR, (FLASH_CR_MER1 | FLASH_CR_MER2));
#else
/* If the erase operation is completed, disable the MER1 Bit */
CLEAR_BIT(FLASH->CR, (FLASH_CR_MER1));
#endif
}
else
{
/*Initialization of PageError variable*/
*PageError = 0xFFFFFFFFU;
for(page_index = pEraseInit->Page; page_index < (pEraseInit->Page + pEraseInit->NbPages); page_index++)
{
FLASH_PageErase(page_index, pEraseInit->Banks);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* If the erase operation is completed, disable the PER Bit */
CLEAR_BIT(FLASH->CR, (FLASH_CR_PER | FLASH_CR_PNB));
if (status != HAL_OK)
{
/* In case of error, stop erase procedure and return the faulty address */
*PageError = page_index;
break;
}
}
}
/* Flush the caches to be sure of the data consistency */
FLASH_FlushCaches();
}
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @brief Perform a mass erase or erase the specified FLASH memory pages with interrupt enabled.
* @param pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
* contains the configuration information for the erasing.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit)
{
HAL_StatusTypeDef status = HAL_OK;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
/* Deactivate the cache if they are activated to avoid data misbehavior */
if(READ_BIT(FLASH->ACR, FLASH_ACR_ICEN) != 0U)
{
/* Disable instruction cache */
__HAL_FLASH_INSTRUCTION_CACHE_DISABLE();
if(READ_BIT(FLASH->ACR, FLASH_ACR_DCEN) != 0U)
{
/* Disable data cache */
__HAL_FLASH_DATA_CACHE_DISABLE();
pFlash.CacheToReactivate = FLASH_CACHE_ICACHE_DCACHE_ENABLED;
}
else
{
pFlash.CacheToReactivate = FLASH_CACHE_ICACHE_ENABLED;
}
}
else if(READ_BIT(FLASH->ACR, FLASH_ACR_DCEN) != 0U)
{
/* Disable data cache */
__HAL_FLASH_DATA_CACHE_DISABLE();
pFlash.CacheToReactivate = FLASH_CACHE_DCACHE_ENABLED;
}
else
{
pFlash.CacheToReactivate = FLASH_CACHE_DISABLED;
}
/* Enable End of Operation and Error interrupts */
__HAL_FLASH_ENABLE_IT(FLASH_IT_EOP | FLASH_IT_OPERR);
pFlash.Bank = pEraseInit->Banks;
if (pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
{
/* Mass erase to be done */
pFlash.ProcedureOnGoing = FLASH_PROC_MASS_ERASE;
FLASH_MassErase(pEraseInit->Banks);
}
else
{
/* Erase by page to be done */
pFlash.ProcedureOnGoing = FLASH_PROC_PAGE_ERASE;
pFlash.NbPagesToErase = pEraseInit->NbPages;
pFlash.Page = pEraseInit->Page;
/*Erase 1st page and wait for IT */
FLASH_PageErase(pEraseInit->Page, pEraseInit->Banks);
}
return status;
}
/**
* @brief Program Option bytes.
* @param pOBInit pointer to an FLASH_OBInitStruct structure that
* contains the configuration information for the programming.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
{
HAL_StatusTypeDef status = HAL_OK;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
/* Write protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_WRP) != 0U)
{
/* Configure of Write protection on the selected area */
if(FLASH_OB_WRPConfig(pOBInit->WRPArea, pOBInit->WRPStartOffset, pOBInit->WRPEndOffset) != HAL_OK)
{
status = HAL_ERROR;
}
}
/* Read protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_RDP) != 0U)
{
/* Configure the Read protection level */
if(FLASH_OB_RDPConfig(pOBInit->RDPLevel) != HAL_OK)
{
status = HAL_ERROR;
}
}
/* User Configuration */
if((pOBInit->OptionType & OPTIONBYTE_USER) != 0U)
{
/* Configure the user option bytes */
if(FLASH_OB_UserConfig(pOBInit->USERType, pOBInit->USERConfig) != HAL_OK)
{
status = HAL_ERROR;
}
}
/* PCROP Configuration */
if((pOBInit->OptionType & OPTIONBYTE_PCROP) != 0U)
{
if (pOBInit->PCROPStartAddr != pOBInit->PCROPEndAddr)
{
/* Configure the Proprietary code readout protection */
if(FLASH_OB_PCROPConfig(pOBInit->PCROPConfig, pOBInit->PCROPStartAddr, pOBInit->PCROPEndAddr) != HAL_OK)
{
status = HAL_ERROR;
}
}
}
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @brief Get the Option bytes configuration.
* @param pOBInit pointer to an FLASH_OBInitStruct structure that contains the
* configuration information.
* @note The fields pOBInit->WRPArea and pOBInit->PCROPConfig should indicate
* which area is requested for the WRP and PCROP, else no information will be returned
*
* @retval None
*/
void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit)
{
pOBInit->OptionType = (OPTIONBYTE_RDP | OPTIONBYTE_USER);
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if((pOBInit->WRPArea == OB_WRPAREA_BANK1_AREAA) || (pOBInit->WRPArea == OB_WRPAREA_BANK1_AREAB) ||
(pOBInit->WRPArea == OB_WRPAREA_BANK2_AREAA) || (pOBInit->WRPArea == OB_WRPAREA_BANK2_AREAB))
#else
if((pOBInit->WRPArea == OB_WRPAREA_BANK1_AREAA) || (pOBInit->WRPArea == OB_WRPAREA_BANK1_AREAB))
#endif
{
pOBInit->OptionType |= OPTIONBYTE_WRP;
/* Get write protection on the selected area */
FLASH_OB_GetWRP(pOBInit->WRPArea, &(pOBInit->WRPStartOffset), &(pOBInit->WRPEndOffset));
}
/* Get Read protection level */
pOBInit->RDPLevel = FLASH_OB_GetRDP();
/* Get the user option bytes */
pOBInit->USERConfig = FLASH_OB_GetUser();
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if((pOBInit->PCROPConfig == FLASH_BANK_1) || (pOBInit->PCROPConfig == FLASH_BANK_2))
#else
if(pOBInit->PCROPConfig == FLASH_BANK_1)
#endif
{
pOBInit->OptionType |= OPTIONBYTE_PCROP;
/* Get the Proprietary code readout protection */
FLASH_OB_GetPCROP(&(pOBInit->PCROPConfig), &(pOBInit->PCROPStartAddr), &(pOBInit->PCROPEndAddr));
}
}
/**
* @}
*/
#if defined (FLASH_CFGR_LVEN)
/** @defgroup FLASHEx_Exported_Functions_Group2 Extended specific configuration functions
* @brief Extended specific configuration functions
*
@verbatim
===============================================================================
##### Extended specific configuration functions #####
===============================================================================
[..]
This subsection provides a set of functions allowing to manage the Extended FLASH
specific configurations.
@endverbatim
* @{
*/
/**
* @brief Configuration of the LVE pin of the Flash (managed by power controller
* or forced to low in order to use an external SMPS)
* @param ConfigLVE Configuration of the LVE pin,
* This parameter can be one of the following values:
* @arg FLASH_LVE_PIN_CTRL: LVE FLASH pin controlled by power controller
* @arg FLASH_LVE_PIN_FORCED: LVE FLASH pin enforced to low (external SMPS used)
*
* @note Before enforcing the LVE pin to low, the SOC should be in low voltage
* range 2 and the voltage VDD12 should be higher than 1.08V and SMPS is ON.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_ConfigLVEPin(uint32_t ConfigLVE)
{
HAL_StatusTypeDef status;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_FLASH_LVE_PIN(ConfigLVE));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if (status == HAL_OK)
{
/* Check that the voltage scaling is range 2 */
if (HAL_PWREx_GetVoltageRange() == PWR_REGULATOR_VOLTAGE_SCALE2)
{
/* Configure the LVEN bit */
MODIFY_REG(FLASH->CFGR, FLASH_CFGR_LVEN, ConfigLVE);
/* Check that the bit has been correctly configured */
if (READ_BIT(FLASH->CFGR, FLASH_CFGR_LVEN) != ConfigLVE)
{
status = HAL_ERROR;
}
}
else
{
/* Not allow to force Flash LVE pin if not in voltage range 2 */
status = HAL_ERROR;
}
}
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @}
*/
#endif /* FLASH_CFGR_LVEN */
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @addtogroup FLASHEx_Private_Functions
* @{
*/
/**
* @brief Mass erase of FLASH memory.
* @param Banks Banks to be erased
* This parameter can be one of the following values:
* @arg FLASH_BANK_1: Bank1 to be erased
* @arg FLASH_BANK_2: Bank2 to be erased
* @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased
* @retval None
*/
static void FLASH_MassErase(uint32_t Banks)
{
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if (READ_BIT(FLASH->OPTR, FLASH_OPTR_DBANK) != 0U)
#endif
{
/* Check the parameters */
assert_param(IS_FLASH_BANK(Banks));
/* Set the Mass Erase Bit for the bank 1 if requested */
if((Banks & FLASH_BANK_1) != 0U)
{
SET_BIT(FLASH->CR, FLASH_CR_MER1);
}
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
/* Set the Mass Erase Bit for the bank 2 if requested */
if((Banks & FLASH_BANK_2) != 0U)
{
SET_BIT(FLASH->CR, FLASH_CR_MER2);
}
#endif
}
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
else
{
SET_BIT(FLASH->CR, (FLASH_CR_MER1 | FLASH_CR_MER2));
}
#endif
/* Proceed to erase all sectors */
SET_BIT(FLASH->CR, FLASH_CR_STRT);
}
/**
* @brief Erase the specified FLASH memory page.
* @param Page FLASH page to erase
* This parameter must be a value between 0 and (max number of pages in the bank - 1)
* @param Banks Bank(s) where the page will be erased
* This parameter can be one of the following values:
* @arg FLASH_BANK_1: Page in bank 1 to be erased
* @arg FLASH_BANK_2: Page in bank 2 to be erased
* @retval None
*/
void FLASH_PageErase(uint32_t Page, uint32_t Banks)
{
/* Check the parameters */
assert_param(IS_FLASH_PAGE(Page));
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if(READ_BIT(FLASH->OPTR, FLASH_OPTR_DBANK) == 0U)
{
CLEAR_BIT(FLASH->CR, FLASH_CR_BKER);
}
else
#endif
{
assert_param(IS_FLASH_BANK_EXCLUSIVE(Banks));
if((Banks & FLASH_BANK_1) != 0U)
{
CLEAR_BIT(FLASH->CR, FLASH_CR_BKER);
}
else
{
SET_BIT(FLASH->CR, FLASH_CR_BKER);
}
}
#else
/* Prevent unused argument(s) compilation warning */
UNUSED(Banks);
#endif
/* Proceed to erase the page */
MODIFY_REG(FLASH->CR, FLASH_CR_PNB, ((Page & 0xFFU) << FLASH_CR_PNB_Pos));
SET_BIT(FLASH->CR, FLASH_CR_PER);
SET_BIT(FLASH->CR, FLASH_CR_STRT);
}
/**
* @brief Flush the instruction and data caches.
* @retval None
*/
void FLASH_FlushCaches(void)
{
FLASH_CacheTypeDef cache = pFlash.CacheToReactivate;
/* Flush instruction cache */
if((cache == FLASH_CACHE_ICACHE_ENABLED) ||
(cache == FLASH_CACHE_ICACHE_DCACHE_ENABLED))
{
/* Reset instruction cache */
__HAL_FLASH_INSTRUCTION_CACHE_RESET();
/* Enable instruction cache */
__HAL_FLASH_INSTRUCTION_CACHE_ENABLE();
}
/* Flush data cache */
if((cache == FLASH_CACHE_DCACHE_ENABLED) ||
(cache == FLASH_CACHE_ICACHE_DCACHE_ENABLED))
{
/* Reset data cache */
__HAL_FLASH_DATA_CACHE_RESET();
/* Enable data cache */
__HAL_FLASH_DATA_CACHE_ENABLE();
}
/* Reset internal variable */
pFlash.CacheToReactivate = FLASH_CACHE_DISABLED;
}
/**
* @brief Configure the write protection of the desired pages.
*
* @note When the memory read protection level is selected (RDP level = 1),
* it is not possible to program or erase Flash memory if the CPU debug
* features are connected (JTAG or single wire) or boot code is being
* executed from RAM or System flash, even if WRP is not activated.
* @note To configure the WRP options, the option lock bit OPTLOCK must be
* cleared with the call of the HAL_FLASH_OB_Unlock() function.
* @note To validate the WRP options, the option bytes must be reloaded
* through the call of the HAL_FLASH_OB_Launch() function.
*
* @param WRPArea specifies the area to be configured.
* This parameter can be one of the following values:
* @arg OB_WRPAREA_BANK1_AREAA: Flash Bank 1 Area A
* @arg OB_WRPAREA_BANK1_AREAB: Flash Bank 1 Area B
* @arg OB_WRPAREA_BANK2_AREAA: Flash Bank 2 Area A (don't apply for STM32L43x/STM32L44x devices)
* @arg OB_WRPAREA_BANK2_AREAB: Flash Bank 2 Area B (don't apply for STM32L43x/STM32L44x devices)
*
* @param WRPStartOffset specifies the start page of the write protected area
* This parameter can be page number between 0 and (max number of pages in the bank - 1)
*
* @param WRDPEndOffset specifies the end page of the write protected area
* This parameter can be page number between WRPStartOffset and (max number of pages in the bank - 1)
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_WRPConfig(uint32_t WRPArea, uint32_t WRPStartOffset, uint32_t WRDPEndOffset)
{
HAL_StatusTypeDef status;
/* Check the parameters */
assert_param(IS_OB_WRPAREA(WRPArea));
assert_param(IS_FLASH_PAGE(WRPStartOffset));
assert_param(IS_FLASH_PAGE(WRDPEndOffset));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
/* Configure the write protected area */
if(WRPArea == OB_WRPAREA_BANK1_AREAA)
{
MODIFY_REG(FLASH->WRP1AR, (FLASH_WRP1AR_WRP1A_STRT | FLASH_WRP1AR_WRP1A_END),
(WRPStartOffset | (WRDPEndOffset << 16)));
}
else if(WRPArea == OB_WRPAREA_BANK1_AREAB)
{
MODIFY_REG(FLASH->WRP1BR, (FLASH_WRP1BR_WRP1B_STRT | FLASH_WRP1BR_WRP1B_END),
(WRPStartOffset | (WRDPEndOffset << 16)));
}
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
else if(WRPArea == OB_WRPAREA_BANK2_AREAA)
{
MODIFY_REG(FLASH->WRP2AR, (FLASH_WRP2AR_WRP2A_STRT | FLASH_WRP2AR_WRP2A_END),
(WRPStartOffset | (WRDPEndOffset << 16)));
}
else if(WRPArea == OB_WRPAREA_BANK2_AREAB)
{
MODIFY_REG(FLASH->WRP2BR, (FLASH_WRP2BR_WRP2B_STRT | FLASH_WRP2BR_WRP2B_END),
(WRPStartOffset | (WRDPEndOffset << 16)));
}
#endif
else
{
/* Nothing to do */
}
/* Set OPTSTRT Bit */
SET_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* If the option byte program operation is completed, disable the OPTSTRT Bit */
CLEAR_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
}
return status;
}
/**
* @brief Set the read protection level.
*
* @note To configure the RDP level, the option lock bit OPTLOCK must be
* cleared with the call of the HAL_FLASH_OB_Unlock() function.
* @note To validate the RDP level, the option bytes must be reloaded
* through the call of the HAL_FLASH_OB_Launch() function.
* @note !!! Warning : When enabling OB_RDP level 2 it's no more possible
* to go back to level 1 or 0 !!!
*
* @param RDPLevel specifies the read protection level.
* This parameter can be one of the following values:
* @arg OB_RDP_LEVEL_0: No protection
* @arg OB_RDP_LEVEL_1: Read protection of the memory
* @arg OB_RDP_LEVEL_2: Full chip protection
*
* @retval HAL status
*/
static HAL_StatusTypeDef FLASH_OB_RDPConfig(uint32_t RDPLevel)
{
HAL_StatusTypeDef status;
/* Check the parameters */
assert_param(IS_OB_RDP_LEVEL(RDPLevel));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
/* Configure the RDP level in the option bytes register */
MODIFY_REG(FLASH->OPTR, FLASH_OPTR_RDP, RDPLevel);
/* Set OPTSTRT Bit */
SET_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* If the option byte program operation is completed, disable the OPTSTRT Bit */
CLEAR_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
}
return status;
}
/**
* @brief Program the FLASH User Option Byte.
*
* @note To configure the user option bytes, the option lock bit OPTLOCK must
* be cleared with the call of the HAL_FLASH_OB_Unlock() function.
* @note To validate the user option bytes, the option bytes must be reloaded
* through the call of the HAL_FLASH_OB_Launch() function.
*
* @param UserType The FLASH User Option Bytes to be modified
* @param UserConfig The FLASH User Option Bytes values:
* BOR_LEV(Bit8-10), nRST_STOP(Bit12), nRST_STDBY(Bit13), IWDG_SW(Bit16),
* IWDG_STOP(Bit17), IWDG_STDBY(Bit18), WWDG_SW(Bit19), BFB2(Bit20),
* DUALBANK(Bit21), nBOOT1(Bit23), SRAM2_PE(Bit24) and SRAM2_RST(Bit25).
*
* @retval HAL status
*/
static HAL_StatusTypeDef FLASH_OB_UserConfig(uint32_t UserType, uint32_t UserConfig)
{
uint32_t optr_reg_val = 0;
uint32_t optr_reg_mask = 0;
HAL_StatusTypeDef status;
/* Check the parameters */
assert_param(IS_OB_USER_TYPE(UserType));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
if((UserType & OB_USER_BOR_LEV) != 0U)
{
/* BOR level option byte should be modified */
assert_param(IS_OB_USER_BOR_LEVEL(UserConfig & FLASH_OPTR_BOR_LEV));
/* Set value and mask for BOR level option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_BOR_LEV);
optr_reg_mask |= FLASH_OPTR_BOR_LEV;
}
if((UserType & OB_USER_nRST_STOP) != 0U)
{
/* nRST_STOP option byte should be modified */
assert_param(IS_OB_USER_STOP(UserConfig & FLASH_OPTR_nRST_STOP));
/* Set value and mask for nRST_STOP option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_nRST_STOP);
optr_reg_mask |= FLASH_OPTR_nRST_STOP;
}
if((UserType & OB_USER_nRST_STDBY) != 0U)
{
/* nRST_STDBY option byte should be modified */
assert_param(IS_OB_USER_STANDBY(UserConfig & FLASH_OPTR_nRST_STDBY));
/* Set value and mask for nRST_STDBY option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_nRST_STDBY);
optr_reg_mask |= FLASH_OPTR_nRST_STDBY;
}
if((UserType & OB_USER_nRST_SHDW) != 0U)
{
/* nRST_SHDW option byte should be modified */
assert_param(IS_OB_USER_SHUTDOWN(UserConfig & FLASH_OPTR_nRST_SHDW));
/* Set value and mask for nRST_SHDW option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_nRST_SHDW);
optr_reg_mask |= FLASH_OPTR_nRST_SHDW;
}
if((UserType & OB_USER_IWDG_SW) != 0U)
{
/* IWDG_SW option byte should be modified */
assert_param(IS_OB_USER_IWDG(UserConfig & FLASH_OPTR_IWDG_SW));
/* Set value and mask for IWDG_SW option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_IWDG_SW);
optr_reg_mask |= FLASH_OPTR_IWDG_SW;
}
if((UserType & OB_USER_IWDG_STOP) != 0U)
{
/* IWDG_STOP option byte should be modified */
assert_param(IS_OB_USER_IWDG_STOP(UserConfig & FLASH_OPTR_IWDG_STOP));
/* Set value and mask for IWDG_STOP option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_IWDG_STOP);
optr_reg_mask |= FLASH_OPTR_IWDG_STOP;
}
if((UserType & OB_USER_IWDG_STDBY) != 0U)
{
/* IWDG_STDBY option byte should be modified */
assert_param(IS_OB_USER_IWDG_STDBY(UserConfig & FLASH_OPTR_IWDG_STDBY));
/* Set value and mask for IWDG_STDBY option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_IWDG_STDBY);
optr_reg_mask |= FLASH_OPTR_IWDG_STDBY;
}
if((UserType & OB_USER_WWDG_SW) != 0U)
{
/* WWDG_SW option byte should be modified */
assert_param(IS_OB_USER_WWDG(UserConfig & FLASH_OPTR_WWDG_SW));
/* Set value and mask for WWDG_SW option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_WWDG_SW);
optr_reg_mask |= FLASH_OPTR_WWDG_SW;
}
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if((UserType & OB_USER_BFB2) != 0U)
{
/* BFB2 option byte should be modified */
assert_param(IS_OB_USER_BFB2(UserConfig & FLASH_OPTR_BFB2));
/* Set value and mask for BFB2 option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_BFB2);
optr_reg_mask |= FLASH_OPTR_BFB2;
}
if((UserType & OB_USER_DUALBANK) != 0U)
{
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
/* DUALBANK option byte should be modified */
assert_param(IS_OB_USER_DUALBANK(UserConfig & FLASH_OPTR_DB1M));
/* Set value and mask for DUALBANK option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_DB1M);
optr_reg_mask |= FLASH_OPTR_DB1M;
#else
/* DUALBANK option byte should be modified */
assert_param(IS_OB_USER_DUALBANK(UserConfig & FLASH_OPTR_DUALBANK));
/* Set value and mask for DUALBANK option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_DUALBANK);
optr_reg_mask |= FLASH_OPTR_DUALBANK;
#endif
}
#endif
if((UserType & OB_USER_nBOOT1) != 0U)
{
/* nBOOT1 option byte should be modified */
assert_param(IS_OB_USER_BOOT1(UserConfig & FLASH_OPTR_nBOOT1));
/* Set value and mask for nBOOT1 option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_nBOOT1);
optr_reg_mask |= FLASH_OPTR_nBOOT1;
}
if((UserType & OB_USER_SRAM2_PE) != 0U)
{
/* SRAM2_PE option byte should be modified */
assert_param(IS_OB_USER_SRAM2_PARITY(UserConfig & FLASH_OPTR_SRAM2_PE));
/* Set value and mask for SRAM2_PE option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_SRAM2_PE);
optr_reg_mask |= FLASH_OPTR_SRAM2_PE;
}
if((UserType & OB_USER_SRAM2_RST) != 0U)
{
/* SRAM2_RST option byte should be modified */
assert_param(IS_OB_USER_SRAM2_RST(UserConfig & FLASH_OPTR_SRAM2_RST));
/* Set value and mask for SRAM2_RST option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_SRAM2_RST);
optr_reg_mask |= FLASH_OPTR_SRAM2_RST;
}
#if defined (STM32L412xx) || defined (STM32L422xx) || defined (STM32L431xx) || defined (STM32L432xx) || defined (STM32L433xx) || \
defined (STM32L442xx) || defined (STM32L443xx) || defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if((UserType & OB_USER_nSWBOOT0) != 0U)
{
/* nSWBOOT0 option byte should be modified */
assert_param(IS_OB_USER_SWBOOT0(UserConfig & FLASH_OPTR_nSWBOOT0));
/* Set value and mask for nSWBOOT0 option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_nSWBOOT0);
optr_reg_mask |= FLASH_OPTR_nSWBOOT0;
}
if((UserType & OB_USER_nBOOT0) != 0U)
{
/* nBOOT0 option byte should be modified */
assert_param(IS_OB_USER_BOOT0(UserConfig & FLASH_OPTR_nBOOT0));
/* Set value and mask for nBOOT0 option byte */
optr_reg_val |= (UserConfig & FLASH_OPTR_nBOOT0);
optr_reg_mask |= FLASH_OPTR_nBOOT0;
}
#endif
/* Configure the option bytes register */
MODIFY_REG(FLASH->OPTR, optr_reg_mask, optr_reg_val);
/* Set OPTSTRT Bit */
SET_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* If the option byte program operation is completed, disable the OPTSTRT Bit */
CLEAR_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
}
return status;
}
/**
* @brief Configure the Proprietary code readout protection of the desired addresses.
*
* @note To configure the PCROP options, the option lock bit OPTLOCK must be
* cleared with the call of the HAL_FLASH_OB_Unlock() function.
* @note To validate the PCROP options, the option bytes must be reloaded
* through the call of the HAL_FLASH_OB_Launch() function.
*
* @param PCROPConfig specifies the configuration (Bank to be configured and PCROP_RDP option).
* This parameter must be a combination of FLASH_BANK_1 or FLASH_BANK_2
* with OB_PCROP_RDP_NOT_ERASE or OB_PCROP_RDP_ERASE
*
* @param PCROPStartAddr specifies the start address of the Proprietary code readout protection
* This parameter can be an address between begin and end of the bank
*
* @param PCROPEndAddr specifies the end address of the Proprietary code readout protection
* This parameter can be an address between PCROPStartAddr and end of the bank
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_PCROPConfig(uint32_t PCROPConfig, uint32_t PCROPStartAddr, uint32_t PCROPEndAddr)
{
HAL_StatusTypeDef status;
uint32_t reg_value;
uint32_t bank1_addr;
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
uint32_t bank2_addr;
#endif
/* Check the parameters */
assert_param(IS_FLASH_BANK_EXCLUSIVE(PCROPConfig & FLASH_BANK_BOTH));
assert_param(IS_OB_PCROP_RDP(PCROPConfig & FLASH_PCROP1ER_PCROP_RDP));
assert_param(IS_FLASH_MAIN_MEM_ADDRESS(PCROPStartAddr));
assert_param(IS_FLASH_MAIN_MEM_ADDRESS(PCROPEndAddr));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
/* Get the information about the bank swapping */
if (READ_BIT(SYSCFG->MEMRMP, SYSCFG_MEMRMP_FB_MODE) == 0U)
{
bank1_addr = FLASH_BASE;
bank2_addr = FLASH_BASE + FLASH_BANK_SIZE;
}
else
{
bank1_addr = FLASH_BASE + FLASH_BANK_SIZE;
bank2_addr = FLASH_BASE;
}
#else
bank1_addr = FLASH_BASE;
#endif
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if (READ_BIT(FLASH->OPTR, FLASH_OPTR_DBANK) == 0U)
{
/* Configure the Proprietary code readout protection */
if((PCROPConfig & FLASH_BANK_BOTH) == FLASH_BANK_1)
{
reg_value = ((PCROPStartAddr - FLASH_BASE) >> 4);
MODIFY_REG(FLASH->PCROP1SR, FLASH_PCROP1SR_PCROP1_STRT, reg_value);
reg_value = ((PCROPEndAddr - FLASH_BASE) >> 4);
MODIFY_REG(FLASH->PCROP1ER, FLASH_PCROP1ER_PCROP1_END, reg_value);
}
else if((PCROPConfig & FLASH_BANK_BOTH) == FLASH_BANK_2)
{
reg_value = ((PCROPStartAddr - FLASH_BASE) >> 4);
MODIFY_REG(FLASH->PCROP2SR, FLASH_PCROP2SR_PCROP2_STRT, reg_value);
reg_value = ((PCROPEndAddr - FLASH_BASE) >> 4);
MODIFY_REG(FLASH->PCROP2ER, FLASH_PCROP2ER_PCROP2_END, reg_value);
}
else
{
/* Nothing to do */
}
}
else
#endif
{
/* Configure the Proprietary code readout protection */
if((PCROPConfig & FLASH_BANK_BOTH) == FLASH_BANK_1)
{
reg_value = ((PCROPStartAddr - bank1_addr) >> 3);
MODIFY_REG(FLASH->PCROP1SR, FLASH_PCROP1SR_PCROP1_STRT, reg_value);
reg_value = ((PCROPEndAddr - bank1_addr) >> 3);
MODIFY_REG(FLASH->PCROP1ER, FLASH_PCROP1ER_PCROP1_END, reg_value);
}
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
else if((PCROPConfig & FLASH_BANK_BOTH) == FLASH_BANK_2)
{
reg_value = ((PCROPStartAddr - bank2_addr) >> 3);
MODIFY_REG(FLASH->PCROP2SR, FLASH_PCROP2SR_PCROP2_STRT, reg_value);
reg_value = ((PCROPEndAddr - bank2_addr) >> 3);
MODIFY_REG(FLASH->PCROP2ER, FLASH_PCROP2ER_PCROP2_END, reg_value);
}
#endif
else
{
/* Nothing to do */
}
}
MODIFY_REG(FLASH->PCROP1ER, FLASH_PCROP1ER_PCROP_RDP, (PCROPConfig & FLASH_PCROP1ER_PCROP_RDP));
/* Set OPTSTRT Bit */
SET_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* If the option byte program operation is completed, disable the OPTSTRT Bit */
CLEAR_BIT(FLASH->CR, FLASH_CR_OPTSTRT);
}
return status;
}
/**
* @brief Return the FLASH Write Protection Option Bytes value.
*
* @param[in] WRPArea: specifies the area to be returned.
* This parameter can be one of the following values:
* @arg OB_WRPAREA_BANK1_AREAA: Flash Bank 1 Area A
* @arg OB_WRPAREA_BANK1_AREAB: Flash Bank 1 Area B
* @arg OB_WRPAREA_BANK2_AREAA: Flash Bank 2 Area A (don't apply to STM32L43x/STM32L44x devices)
* @arg OB_WRPAREA_BANK2_AREAB: Flash Bank 2 Area B (don't apply to STM32L43x/STM32L44x devices)
*
* @param[out] WRPStartOffset: specifies the address where to copied the start page
* of the write protected area
*
* @param[out] WRDPEndOffset: specifies the address where to copied the end page of
* the write protected area
*
* @retval None
*/
static void FLASH_OB_GetWRP(uint32_t WRPArea, uint32_t * WRPStartOffset, uint32_t * WRDPEndOffset)
{
/* Get the configuration of the write protected area */
if(WRPArea == OB_WRPAREA_BANK1_AREAA)
{
*WRPStartOffset = READ_BIT(FLASH->WRP1AR, FLASH_WRP1AR_WRP1A_STRT);
*WRDPEndOffset = (READ_BIT(FLASH->WRP1AR, FLASH_WRP1AR_WRP1A_END) >> 16);
}
else if(WRPArea == OB_WRPAREA_BANK1_AREAB)
{
*WRPStartOffset = READ_BIT(FLASH->WRP1BR, FLASH_WRP1BR_WRP1B_STRT);
*WRDPEndOffset = (READ_BIT(FLASH->WRP1BR, FLASH_WRP1BR_WRP1B_END) >> 16);
}
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
else if(WRPArea == OB_WRPAREA_BANK2_AREAA)
{
*WRPStartOffset = READ_BIT(FLASH->WRP2AR, FLASH_WRP2AR_WRP2A_STRT);
*WRDPEndOffset = (READ_BIT(FLASH->WRP2AR, FLASH_WRP2AR_WRP2A_END) >> 16);
}
else if(WRPArea == OB_WRPAREA_BANK2_AREAB)
{
*WRPStartOffset = READ_BIT(FLASH->WRP2BR, FLASH_WRP2BR_WRP2B_STRT);
*WRDPEndOffset = (READ_BIT(FLASH->WRP2BR, FLASH_WRP2BR_WRP2B_END) >> 16);
}
#endif
else
{
/* Nothing to do */
}
}
/**
* @brief Return the FLASH Read Protection level.
* @retval FLASH ReadOut Protection Status:
* This return value can be one of the following values:
* @arg OB_RDP_LEVEL_0: No protection
* @arg OB_RDP_LEVEL_1: Read protection of the memory
* @arg OB_RDP_LEVEL_2: Full chip protection
*/
static uint32_t FLASH_OB_GetRDP(void)
{
uint32_t rdp_level = READ_BIT(FLASH->OPTR, FLASH_OPTR_RDP);
if ((rdp_level != OB_RDP_LEVEL_0) && (rdp_level != OB_RDP_LEVEL_2))
{
return (OB_RDP_LEVEL_1);
}
else
{
return (READ_BIT(FLASH->OPTR, FLASH_OPTR_RDP));
}
}
/**
* @brief Return the FLASH User Option Byte value.
* @retval The FLASH User Option Bytes values:
* For STM32L47x/STM32L48x devices :
* BOR_LEV(Bit8-10), nRST_STOP(Bit12), nRST_STDBY(Bit13), nRST_SHDW(Bit14),
* IWDG_SW(Bit16), IWDG_STOP(Bit17), IWDG_STDBY(Bit18), WWDG_SW(Bit19),
* BFB2(Bit20), DUALBANK(Bit21), nBOOT1(Bit23), SRAM2_PE(Bit24) and SRAM2_RST(Bit25).
* For STM32L43x/STM32L44x devices :
* BOR_LEV(Bit8-10), nRST_STOP(Bit12), nRST_STDBY(Bit13), nRST_SHDW(Bit14),
* IWDG_SW(Bit16), IWDG_STOP(Bit17), IWDG_STDBY(Bit18), WWDG_SW(Bit19),
* nBOOT1(Bit23), SRAM2_PE(Bit24), SRAM2_RST(Bit25), nSWBOOT0(Bit26) and nBOOT0(Bit27).
*/
static uint32_t FLASH_OB_GetUser(void)
{
uint32_t user_config = READ_REG(FLASH->OPTR);
CLEAR_BIT(user_config, FLASH_OPTR_RDP);
return user_config;
}
/**
* @brief Return the FLASH Write Protection Option Bytes value.
*
* @param PCROPConfig [inout]: specifies the configuration (Bank to be configured and PCROP_RDP option).
* This parameter must be a combination of FLASH_BANK_1 or FLASH_BANK_2
* with OB_PCROP_RDP_NOT_ERASE or OB_PCROP_RDP_ERASE
*
* @param PCROPStartAddr [out]: specifies the address where to copied the start address
* of the Proprietary code readout protection
*
* @param PCROPEndAddr [out]: specifies the address where to copied the end address of
* the Proprietary code readout protection
*
* @retval None
*/
static void FLASH_OB_GetPCROP(uint32_t * PCROPConfig, uint32_t * PCROPStartAddr, uint32_t * PCROPEndAddr)
{
uint32_t reg_value;
uint32_t bank1_addr;
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
uint32_t bank2_addr;
#endif
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
/* Get the information about the bank swapping */
if (READ_BIT(SYSCFG->MEMRMP, SYSCFG_MEMRMP_FB_MODE) == 0U)
{
bank1_addr = FLASH_BASE;
bank2_addr = FLASH_BASE + FLASH_BANK_SIZE;
}
else
{
bank1_addr = FLASH_BASE + FLASH_BANK_SIZE;
bank2_addr = FLASH_BASE;
}
#else
bank1_addr = FLASH_BASE;
#endif
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
if (READ_BIT(FLASH->OPTR, FLASH_OPTR_DBANK) == 0U)
{
if(((*PCROPConfig) & FLASH_BANK_BOTH) == FLASH_BANK_1)
{
reg_value = (READ_REG(FLASH->PCROP1SR) & FLASH_PCROP1SR_PCROP1_STRT);
*PCROPStartAddr = (reg_value << 4) + FLASH_BASE;
reg_value = (READ_REG(FLASH->PCROP1ER) & FLASH_PCROP1ER_PCROP1_END);
*PCROPEndAddr = (reg_value << 4) + FLASH_BASE + 0xFU;
}
else if(((*PCROPConfig) & FLASH_BANK_BOTH) == FLASH_BANK_2)
{
reg_value = (READ_REG(FLASH->PCROP2SR) & FLASH_PCROP2SR_PCROP2_STRT);
*PCROPStartAddr = (reg_value << 4) + FLASH_BASE;
reg_value = (READ_REG(FLASH->PCROP2ER) & FLASH_PCROP2ER_PCROP2_END);
*PCROPEndAddr = (reg_value << 4) + FLASH_BASE + 0xFU;;
}
else
{
/* Nothing to do */
}
}
else
#endif
{
if(((*PCROPConfig) & FLASH_BANK_BOTH) == FLASH_BANK_1)
{
reg_value = (READ_REG(FLASH->PCROP1SR) & FLASH_PCROP1SR_PCROP1_STRT);
*PCROPStartAddr = (reg_value << 3) + bank1_addr;
reg_value = (READ_REG(FLASH->PCROP1ER) & FLASH_PCROP1ER_PCROP1_END);
*PCROPEndAddr = (reg_value << 3) + bank1_addr + 0x7U;
}
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || \
defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
else if(((*PCROPConfig) & FLASH_BANK_BOTH) == FLASH_BANK_2)
{
reg_value = (READ_REG(FLASH->PCROP2SR) & FLASH_PCROP2SR_PCROP2_STRT);
*PCROPStartAddr = (reg_value << 3) + bank2_addr;
reg_value = (READ_REG(FLASH->PCROP2ER) & FLASH_PCROP2ER_PCROP2_END);
*PCROPEndAddr = (reg_value << 3) + bank2_addr + 0x7U;
}
#endif
else
{
/* Nothing to do */
}
}
*PCROPConfig |= (READ_REG(FLASH->PCROP1ER) & FLASH_PCROP1ER_PCROP_RDP);
}
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_FLASH_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/