GitBucket
Newer
//*****************************************************************************
//
// am_bsp_pins.c
//! @file
//!
//! @brief BSP pin configuration definitions.
//!
//! @addtogroup BSP Board Support Package (BSP)
//! @addtogroup apollo3_evb_bsp BSP for the Apollo3 Engineering Board
//! @ingroup BSP
//! @{
//
//*****************************************************************************
//*****************************************************************************
//
// Copyright (c) 2019, Ambiq Micro
// All rights reserved.
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// 1. Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// 2. Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// 3. Neither the name of the copyright holder nor the names of its
// contributors may be used to endorse or promote products derived from this
// software without specific prior written permission.
//
// Third party software included in this distribution is subject to the
// additional license terms as defined in the /docs/licenses directory.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// This is part of revision 2.2.0-hotfix-2.2.1 of the AmbiqSuite Development Package.
//
//*****************************************************************************
// SPDX-License-Identifier: BSD-3-Clause
#include "am_bsp.h"
//*****************************************************************************
//
// COM_UART_TX pin: This pin is the COM_UART transmit pin.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_COM_UART_TX =
{
.uFuncSel = AM_HAL_PIN_48_UART0TX,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_2MA
};
//*****************************************************************************
//
// COM_UART_RX pin: This pin is the COM_UART receive pin.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_COM_UART_RX =
{
.uFuncSel = AM_HAL_PIN_49_UART0RX
};
//*****************************************************************************
//
// IOM0_CS pin: I/O Master 0 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_CS =
{
.uFuncSel = AM_HAL_PIN_11_NCE11,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 0,
.uNCE = 0,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM0_CS3 pin: I/O Master 0 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_CS3 =
{
.uFuncSel = AM_HAL_PIN_15_NCE15,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 0,
.uNCE = 3,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM0_MISO pin: I/O Master 0 SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_MISO =
{
.uFuncSel = AM_HAL_PIN_6_M0MISO,
.uIOMnum = 0
};
//*****************************************************************************
//
// IOM0_MOSI pin: I/O Master 0 SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_MOSI =
{
.uFuncSel = AM_HAL_PIN_7_M0MOSI,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 0
};
//*****************************************************************************
//
// IOM0_SCK pin: I/O Master 0 SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_SCK =
{
.uFuncSel = AM_HAL_PIN_5_M0SCK,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 0
};
//*****************************************************************************
//
// IOM0_SCL pin: I/O Master 0 I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_SCL =
{
.uFuncSel = AM_HAL_PIN_5_M0SCL,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 0
};
//*****************************************************************************
//
// IOM0_SDA pin: I/O Master 0 I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM0_SDA =
{
.uFuncSel = AM_HAL_PIN_6_M0SDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 0
};
//*****************************************************************************
//
// IOM1_CS pin: I/O Master 1 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM1_CS =
{
.uFuncSel = AM_HAL_PIN_14_NCE14,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 1,
.uNCE = 2,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM1_MISO pin: I/O Master 1 SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM1_MISO =
{
.uFuncSel = AM_HAL_PIN_9_M1MISO,
.uIOMnum = 1
};
//*****************************************************************************
//
// IOM1_MOSI pin: I/O Master 1 SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM1_MOSI =
{
.uFuncSel = AM_HAL_PIN_10_M1MOSI,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 1
};
//*****************************************************************************
//
// IOM1_SCK pin: I/O Master 1 SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM1_SCK =
{
.uFuncSel = AM_HAL_PIN_8_M1SCK,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 1
};
//*****************************************************************************
//
// IOM1_SCL pin: I/O Master 1 I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM1_SCL =
{
.uFuncSel = AM_HAL_PIN_8_M1SCL,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 1
};
//*****************************************************************************
//
// IOM1_SDA pin: I/O Master 1 I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM1_SDA =
{
.uFuncSel = AM_HAL_PIN_9_M1SDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 1
};
//*****************************************************************************
//
// IOM2_CS pin: I/O Master 2 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM2_CS =
{
.uFuncSel = AM_HAL_PIN_15_NCE15,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 2,
.uNCE = 3,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM2_MISO pin: I/O Master 2 SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM2_MISO =
{
.uFuncSel = AM_HAL_PIN_25_M2MISO,
.uIOMnum = 2
};
//*****************************************************************************
//
// IOM2_MOSI pin: I/O Master 2 SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM2_MOSI =
{
.uFuncSel = AM_HAL_PIN_28_M2MOSI,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 2
};
//*****************************************************************************
//
// IOM2_SCK pin: I/O Master 2 SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM2_SCK =
{
.uFuncSel = AM_HAL_PIN_27_M2SCK,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 2
};
//*****************************************************************************
//
// IOM2_SCL pin: I/O Master 2 I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM2_SCL =
{
.uFuncSel = AM_HAL_PIN_27_M2SCL,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 2
};
//*****************************************************************************
//
// IOM2_SDA pin: I/O Master 2 I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM2_SDA =
{
.uFuncSel = AM_HAL_PIN_25_M2SDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 2
};
//*****************************************************************************
//
// IOM3_CS pin: I/O Master 3 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM3_CS =
{
.uFuncSel = AM_HAL_PIN_12_NCE12,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 3,
.uNCE = 0,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM3_MISO pin: I/O Master 3 SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM3_MISO =
{
.uFuncSel = AM_HAL_PIN_43_M3MISO,
.uIOMnum = 3
};
//*****************************************************************************
//
// IOM3_MOSI pin: I/O Master 3 SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM3_MOSI =
{
.uFuncSel = AM_HAL_PIN_38_M3MOSI,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 3
};
//*****************************************************************************
//
// IOM3_SCK pin: I/O Master 3 SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM3_SCK =
{
.uFuncSel = AM_HAL_PIN_42_M3SCK,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 3
};
//*****************************************************************************
//
// IOM3_SCL pin: I/O Master 3 I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM3_SCL =
{
.uFuncSel = AM_HAL_PIN_42_M3SCL,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 3
};
//*****************************************************************************
//
// IOM3_SDA pin: I/O Master 3 I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM3_SDA =
{
.uFuncSel = AM_HAL_PIN_43_M3SDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 3
};
//*****************************************************************************
//
// IOM4_CS pin: I/O Master 4 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM4_CS =
{
.uFuncSel = AM_HAL_PIN_13_NCE13,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 4,
.uNCE = 1,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM4_MISO pin: I/O Master 4 SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM4_MISO =
{
.uFuncSel = AM_HAL_PIN_40_M4MISO,
.uIOMnum = 4
};
//*****************************************************************************
//
// IOM4_MOSI pin: I/O Master 4 SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM4_MOSI =
{
.uFuncSel = AM_HAL_PIN_44_M4MOSI,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 4
};
//*****************************************************************************
//
// IOM4_SCK pin: I/O Master 4 SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM4_SCK =
{
.uFuncSel = AM_HAL_PIN_39_M4SCK,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 4
};
//*****************************************************************************
//
// IOM4_SCL pin: I/O Master 4 I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM4_SCL =
{
.uFuncSel = AM_HAL_PIN_39_M4SCL,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 4
};
//*****************************************************************************
//
// IOM4_SDA pin: I/O Master 4 I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM4_SDA =
{
.uFuncSel = AM_HAL_PIN_40_M4SDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 4
};
//*****************************************************************************
//
// IOM5_CS pin: I/O Master 5 chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM5_CS =
{
.uFuncSel = AM_HAL_PIN_16_NCE16,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 5,
.uNCE = 0,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOM5_MISO pin: I/O Master 5 SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM5_MISO =
{
.uFuncSel = AM_HAL_PIN_49_M5MISO,
.uIOMnum = 5
};
//*****************************************************************************
//
// IOM5_MOSI pin: I/O Master 5 SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM5_MOSI =
{
.uFuncSel = AM_HAL_PIN_47_M5MOSI,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 5
};
//*****************************************************************************
//
// IOM5_SCK pin: I/O Master 5 SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM5_SCK =
{
.uFuncSel = AM_HAL_PIN_48_M5SCK,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.uIOMnum = 5
};
//*****************************************************************************
//
// IOM5_SCL pin: I/O Master 5 I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM5_SCL =
{
.uFuncSel = AM_HAL_PIN_48_M5SCL,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 5
};
//*****************************************************************************
//
// IOM5_SDA pin: I/O Master 5 I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOM5_SDA =
{
.uFuncSel = AM_HAL_PIN_49_M5SDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN,
.uIOMnum = 5
};
//*****************************************************************************
//
// MSPI_CE0 pin: MSPI chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_CE0 =
{
.uFuncSel = AM_HAL_PIN_19_NCE19,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6,
.uNCE = 0,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// MSPI_CE1 pin: MSPI chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_CE1 =
{
.uFuncSel = AM_HAL_PIN_41_NCE41,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_PUSHPULL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_NONE,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6,
.uNCE = 1,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// MSPI_D0 pin: MSPI data 0.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D0 =
{
.uFuncSel = AM_HAL_PIN_22_MSPI0,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D1 pin: MSPI data 1.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D1 =
{
.uFuncSel = AM_HAL_PIN_26_MSPI1,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D2 pin: MSPI data 2.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D2 =
{
.uFuncSel = AM_HAL_PIN_4_MSPI2,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D3 pin: MSPI data 3.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D3 =
{
.uFuncSel = AM_HAL_PIN_23_MSPI13,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D4 pin: MSPI data 4.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D4 =
{
.uFuncSel = AM_HAL_PIN_0_MSPI4,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D5 pin: MSPI data 5.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D5 =
{
.uFuncSel = AM_HAL_PIN_1_MSPI5,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D6 pin: MSPI data 6.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D6 =
{
.uFuncSel = AM_HAL_PIN_2_MSPI6,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_D7 pin: MSPI data 7.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_D7 =
{
.uFuncSel = AM_HAL_PIN_3_MSPI7,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_8MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// MSPI_SCK pin: MSPI clock.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_MSPI_SCK =
{
.uFuncSel = AM_HAL_PIN_24_MSPI8,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA,
.eIntDir = AM_HAL_GPIO_PIN_INTDIR_LO2HI,
.uIOMnum = 6
};
//*****************************************************************************
//
// IOS_CE pin: I/O Slave chip select.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOS_CE =
{
.uFuncSel = AM_HAL_PIN_3_SLnCE,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_ENABLE,
.uNCE = 0,
.eCEpol = AM_HAL_GPIO_PIN_CEPOL_ACTIVELOW
};
//*****************************************************************************
//
// IOS_MISO pin: I/O Slave SPI MISO signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOS_MISO =
{
.uFuncSel = AM_HAL_PIN_2_SLMISO,
.eDriveStrength = AM_HAL_GPIO_PIN_DRIVESTRENGTH_12MA
};
//*****************************************************************************
//
// IOS_MOSI pin: I/O Slave SPI MOSI signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOS_MOSI =
{
.uFuncSel = AM_HAL_PIN_1_SLMOSI,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_ENABLE
};
//*****************************************************************************
//
// IOS_SCK pin: I/O Slave SPI SCK signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOS_SCK =
{
.uFuncSel = AM_HAL_PIN_0_SLSCK,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_ENABLE
};
//*****************************************************************************
//
// IOS_SCL pin: I/O Slave I2C clock signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOS_SCL =
{
.uFuncSel = AM_HAL_PIN_0_SLSCL,
.eGPInput = AM_HAL_GPIO_PIN_INPUT_ENABLE
};
//*****************************************************************************
//
// IOS_SDA pin: I/O Slave I2C data signal.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_IOS_SDA =
{
.uFuncSel = AM_HAL_PIN_1_SLSDAWIR3,
.ePullup = AM_HAL_GPIO_PIN_PULLUP_1_5K,
.eGPOutcfg = AM_HAL_GPIO_PIN_OUTCFG_OPENDRAIN
};
//*****************************************************************************
//
// SWDCK pin: Cortex Serial Wire DCK.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_SWDCK =
{
.uFuncSel = AM_HAL_PIN_20_SWDCK
};
//*****************************************************************************
//
// SWDIO pin: Cortex Serial Wire DIO.
//
//*****************************************************************************
const am_hal_gpio_pincfg_t g_AM_BSP_GPIO_SWDIO =
{
.uFuncSel = AM_HAL_PIN_21_SWDIO
};
//*****************************************************************************
//
// End Doxygen group.
//! @}
//
//*****************************************************************************