GitBucket
Newer
/**
******************************************************************************
* @file stm32wlxx_hal_rtc_ex.h
* @author MCD Application Team
* @brief Header file of RTC HAL Extended module.
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2020 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32WLxx_HAL_RTC_EX_H
#define STM32WLxx_HAL_RTC_EX_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32wlxx_hal_def.h"
/** @addtogroup STM32WLxx_HAL_Driver
* @{
*/
/** @defgroup RTCEx RTCEx
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup RTCEx_Exported_Types RTCEx Exported Types
* @{
*/
/** @defgroup RTCEx_Tamper_structure_definition RTCEx Tamper structure definition
* @{
*/
typedef struct
{
uint32_t Tamper; /*!< Specifies the Tamper Pin.
This parameter can be a value of @ref RTCEx_Tamper_Pins */
uint32_t Trigger; /*!< Specifies the Tamper Trigger.
This parameter can be a value of @ref RTCEx_Tamper_Trigger */
uint32_t NoErase; /*!< Specifies the Tamper no erase mode.
This parameter can be a value of @ref RTCEx_Tamper_EraseBackUp */
uint32_t MaskFlag; /*!< Specifies the Tamper Flag masking.
This parameter can be a value of @ref RTCEx_Tamper_MaskFlag */
uint32_t Filter; /*!< Specifies the TAMP Filter Tamper.
This parameter can be a value of @ref RTCEx_Tamper_Filter */
uint32_t SamplingFrequency; /*!< Specifies the sampling frequency.
This parameter can be a value of @ref RTCEx_Tamper_Sampling_Frequencies */
uint32_t PrechargeDuration; /*!< Specifies the Precharge Duration .
This parameter can be a value of @ref RTCEx_Tamper_Pin_Precharge_Duration */
uint32_t TamperPullUp; /*!< Specifies the Tamper PullUp .
This parameter can be a value of @ref RTCEx_Tamper_Pull_UP */
uint32_t TimeStampOnTamperDetection; /*!< Specifies the TimeStampOnTamperDetection.
This parameter can be a value of @ref RTCEx_Tamper_TimeStampOnTamperDetection */
} RTC_TamperTypeDef;
/**
* @}
*/
/** @defgroup RTCEx_Internal_Tamper_structure_definition RTCEx Internal Tamper structure definition
* @{
*/
typedef struct
{
uint32_t IntTamper; /*!< Specifies the Internal Tamper Pin.
This parameter can be a value of @ref RTCEx_Internal_Tamper_Pins */
uint32_t TimeStampOnTamperDetection; /*!< Specifies the TimeStampOnTamperDetection.
This parameter can be a value of @ref RTCEx_Tamper_TimeStampOnTamperDetection */
uint32_t NoErase; /*!< Specifies the internal Tamper no erase mode.
This parameter can be a value of @ref RTCEx_Tamper_EraseBackUp */
} RTC_InternalTamperTypeDef;
/**
* @}
*/
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup RTCEx_Exported_Constants RTCEx Exported Constants
* @{
*/
/** @defgroup RTCEx_Time_Stamp_Edges_definitions RTCEx Time Stamp Edges definition
* @{
*/
#define RTC_TIMESTAMPEDGE_RISING 0x00000000u
#define RTC_TIMESTAMPEDGE_FALLING RTC_CR_TSEDGE
/**
* @}
*/
/** @defgroup RTCEx_TimeStamp_Pin_Selections RTCEx TimeStamp Pin Selection
* @{
*/
#define RTC_TIMESTAMPPIN_DEFAULT 0x00000000u
/**
* @}
*/
/** @defgroup RTCEx_Wakeup_Timer_Definitions RTCEx Wakeup Timer Definitions
* @{
*/
#define RTC_WAKEUPCLOCK_RTCCLK_DIV16 0x00000000u
#define RTC_WAKEUPCLOCK_RTCCLK_DIV8 RTC_CR_WUCKSEL_0
#define RTC_WAKEUPCLOCK_RTCCLK_DIV4 RTC_CR_WUCKSEL_1
#define RTC_WAKEUPCLOCK_RTCCLK_DIV2 (RTC_CR_WUCKSEL_0 | RTC_CR_WUCKSEL_1)
#define RTC_WAKEUPCLOCK_CK_SPRE_16BITS RTC_CR_WUCKSEL_2
#define RTC_WAKEUPCLOCK_CK_SPRE_17BITS (RTC_CR_WUCKSEL_1 | RTC_CR_WUCKSEL_2)
/**
* @}
*/
/** @defgroup RTCEx_Smooth_calib_period_Definitions RTCEx Smooth calib period Definitions
* @{
*/
#define RTC_SMOOTHCALIB_PERIOD_32SEC 0x00000000u /*!< If RTCCLK = 32768 Hz, Smooth calibration
period is 32s, else 2exp20 RTCCLK pulses */
#define RTC_SMOOTHCALIB_PERIOD_16SEC RTC_CALR_CALW16 /*!< If RTCCLK = 32768 Hz, Smooth calibration
period is 16s, else 2exp19 RTCCLK pulses */
#define RTC_SMOOTHCALIB_PERIOD_8SEC RTC_CALR_CALW8 /*!< If RTCCLK = 32768 Hz, Smooth calibration
period is 8s, else 2exp18 RTCCLK pulses */
/**
* @}
*/
/** @defgroup RTCEx_Smooth_calib_Plus_pulses_Definitions RTCEx Smooth calib Plus pulses Definitions
* @{
*/
#define RTC_SMOOTHCALIB_PLUSPULSES_SET RTC_CALR_CALP /*!< The number of RTCCLK pulses added
during a X -second window = Y - CALM[8:0]
with Y = 512, 256, 128 when X = 32, 16, 8 */
#define RTC_SMOOTHCALIB_PLUSPULSES_RESET 0x00000000u /*!< The number of RTCCLK pulses subbstited
during a 32-second window = CALM[8:0] */
/**
* @}
*/
/** @defgroup RTCEx_Smooth_calib_low_power_Definitions RTCEx Smooth calib Low Power Definitions
* @{
*/
#define RTC_LPCAL_SET RTC_CALR_LPCAL /*!< Calibration window is 220 ck_apre,
which is the required configuration for
ultra-low consumption mode. */
#define RTC_LPCAL_RESET 0x00000000u /*!< Calibration window is 220 RTCCLK,
which is a high-consumption mode.
This mode should be set only when less
than 32s calibration window is required. */
/**
* @}
*/
/** @defgroup RTCEx_Calib_Output_selection_Definitions RTCEx Calib Output selection Definitions
* @{
*/
#define RTC_CALIBOUTPUT_512HZ 0x00000000u
#define RTC_CALIBOUTPUT_1HZ RTC_CR_COSEL
/**
* @}
*/
/** @defgroup RTCEx_Add_1_Second_Parameter_Definition RTCEx Add 1 Second Parameter Definitions
* @{
*/
#define RTC_SHIFTADD1S_RESET 0x00000000u
#define RTC_SHIFTADD1S_SET RTC_SHIFTR_ADD1S
/**
* @}
*/
/** @defgroup RTCEx_Tamper_Pins RTCEx Tamper Pins Definition
* @{
*/
#define RTC_TAMPER_1 TAMP_CR1_TAMP1E
#define RTC_TAMPER_2 TAMP_CR1_TAMP2E
#define RTC_TAMPER_3 TAMP_CR1_TAMP3E
#define RTC_TAMPER_ALL (TAMP_CR1_TAMP1E | TAMP_CR1_TAMP2E | TAMP_CR1_TAMP3E)
/**
* @}
*/
/** @defgroup RTCEx_Internal_Tamper_Pins RTCEx Internal Tamper Pins Definition
* @{
*/
#define RTC_INT_TAMPER_3 TAMP_CR1_ITAMP3E
#define RTC_INT_TAMPER_5 TAMP_CR1_ITAMP5E
#define RTC_INT_TAMPER_6 TAMP_CR1_ITAMP6E
#define RTC_INT_TAMPER_8 TAMP_CR1_ITAMP8E
#define RTC_INT_TAMPER_ALL (TAMP_CR1_ITAMP3E | TAMP_CR1_ITAMP5E | TAMP_CR1_ITAMP6E | TAMP_CR1_ITAMP8E)
/**
* @}
*/
/** @defgroup RTCEx_Tamper_Trigger RTCEx Tamper Trigger
* @{
*/
#define RTC_TAMPERTRIGGER_RISINGEDGE 0x00u /*!< Warning : Filter must be RTC_TAMPERFILTER_DISABLE */
#define RTC_TAMPERTRIGGER_FALLINGEDGE 0x01u /*!< Warning : Filter must be RTC_TAMPERFILTER_DISABLE */
#define RTC_TAMPERTRIGGER_LOWLEVEL 0x02u /*!< Warning : Filter must not be RTC_TAMPERFILTER_DISABLE */
#define RTC_TAMPERTRIGGER_HIGHLEVEL 0x03u /*!< Warning : Filter must not be RTC_TAMPERFILTER_DISABLE */
/**
* @}
*/
/** @defgroup RTCEx_Tamper_MaskFlag RTCEx Tamper MaskFlag
* @{
*/
#define RTC_TAMPERMASK_FLAG_DISABLE 0x00u
#define RTC_TAMPERMASK_FLAG_ENABLE 0x01u
/**
* @}
*/
/** @defgroup RTCEx_Tamper_EraseBackUp RTCEx Tamper EraseBackUp
* @{
*/
#define RTC_TAMPER_ERASE_BACKUP_ENABLE 0x00u
#define RTC_TAMPER_ERASE_BACKUP_DISABLE 0x01u
/**
* @}
*/
/** @defgroup RTCEx_Tamper_Filter RTCEx Tamper Filter
* @{
*/
#define RTC_TAMPERFILTER_DISABLE 0x00000000U /*!< Tamper filter is disabled */
#define RTC_TAMPERFILTER_2SAMPLE TAMP_FLTCR_TAMPFLT_0 /*!< Tamper is activated after 2
consecutive samples at the active level */
#define RTC_TAMPERFILTER_4SAMPLE TAMP_FLTCR_TAMPFLT_1 /*!< Tamper is activated after 4
consecutive samples at the active level */
#define RTC_TAMPERFILTER_8SAMPLE TAMP_FLTCR_TAMPFLT /*!< Tamper is activated after 8
consecutive samples at the active level */
/**
* @}
*/
/** @defgroup RTCEx_Tamper_Sampling_Frequencies RTCEx Tamper Sampling Frequencies
* @{
*/
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV32768 0x00000000U /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 32768 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV16384 TAMP_FLTCR_TAMPFREQ_0 /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 16384 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV8192 TAMP_FLTCR_TAMPFREQ_1 /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 8192 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV4096 (TAMP_FLTCR_TAMPFREQ_0 | TAMP_FLTCR_TAMPFREQ_1) /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 4096 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV2048 TAMP_FLTCR_TAMPFREQ_2 /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 2048 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV1024 (TAMP_FLTCR_TAMPFREQ_0 | TAMP_FLTCR_TAMPFREQ_2) /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 1024 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV512 (TAMP_FLTCR_TAMPFREQ_1 | TAMP_FLTCR_TAMPFREQ_2) /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 512 */
#define RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV256 (TAMP_FLTCR_TAMPFREQ_0 | TAMP_FLTCR_TAMPFREQ_1 | \
TAMP_FLTCR_TAMPFREQ_2) /*!< Each of the tamper inputs are sampled
with a frequency = RTCCLK / 256 */
/**
* @}
*/
/** @defgroup RTCEx_Tamper_Pin_Precharge_Duration RTCEx Tamper Pin Precharge Duration
* @{
*/
#define RTC_TAMPERPRECHARGEDURATION_1RTCCLK 0x00000000U /*!< Tamper pins are pre-charged before
sampling during 1 RTCCLK cycle */
#define RTC_TAMPERPRECHARGEDURATION_2RTCCLK TAMP_FLTCR_TAMPPRCH_0 /*!< Tamper pins are pre-charged before
sampling during 2 RTCCLK cycles */
#define RTC_TAMPERPRECHARGEDURATION_4RTCCLK TAMP_FLTCR_TAMPPRCH_1 /*!< Tamper pins are pre-charged before
sampling during 4 RTCCLK cycles */
#define RTC_TAMPERPRECHARGEDURATION_8RTCCLK (TAMP_FLTCR_TAMPPRCH_0 | TAMP_FLTCR_TAMPPRCH_1) /*!< Tamper pins are pre-charged before
sampling during 8 RTCCLK cycles */
/**
* @}
*/
/** @defgroup RTCEx_Tamper_Pull_UP RTCEx Tamper Pull UP
* @{
*/
#define RTC_TAMPER_PULLUP_ENABLE 0x00000000u /*!< Tamper pins are pre-charged before sampling */
#define RTC_TAMPER_PULLUP_DISABLE TAMP_FLTCR_TAMPPUDIS /*!< Tamper pins pre-charge is disabled */
/**
* @}
*/
/** @defgroup RTCEx_Tamper_TimeStampOnTamperDetection RTCEx Tamper TimeStamp On Tamper Detection Definitions
* @{
*/
#define RTC_TIMESTAMPONTAMPERDETECTION_DISABLE 0x00000000u /*!< TimeStamp on Tamper Detection event is not saved */
#define RTC_TIMESTAMPONTAMPERDETECTION_ENABLE RTC_CR_TAMPTS /*!< TimeStamp on Tamper Detection event saved */
/**
* @}
*/
/** @defgroup RTCEx_Internal_Tamper_Interrupt RTCEx Internal Tamper Interrupt
* @{
*/
#define RTC_IT_TAMP_1 TAMP_IER_TAMP1IE /*!< Tamper 1 Interrupt */
#define RTC_IT_TAMP_2 TAMP_IER_TAMP2IE /*!< Tamper 2 Interrupt */
#define RTC_IT_TAMP_3 TAMP_IER_TAMP3IE /*!< Tamper 3 Interrupt */
#define RTC_IT_TAMP_ALL (TAMP_IER_TAMP1IE | TAMP_IER_TAMP2IE | TAMP_IER_TAMP3IE)
#define RTC_IT_INT_TAMP_3 TAMP_IER_ITAMP3IE
#define RTC_IT_INT_TAMP_5 TAMP_IER_ITAMP5IE
#define RTC_IT_INT_TAMP_6 TAMP_IER_ITAMP6IE
#define RTC_IT_INT_TAMP_8 TAMP_IER_ITAMP8IE
#define RTC_IT_INT_TAMP_ALL (TAMP_IER_ITAMP3IE | TAMP_IER_ITAMP5IE | TAMP_IER_ITAMP6IE | TAMP_IER_ITAMP8IE)
/**
* @}
*/
/** @defgroup RTCEx_Flags RTCEx Flags
* @{
*/
#define RTC_FLAG_TAMP_1 TAMP_SR_TAMP1F
#define RTC_FLAG_TAMP_2 TAMP_SR_TAMP2F
#define RTC_FLAG_TAMP_3 TAMP_SR_TAMP3F
#define RTC_FLAG_TAMP_ALL (RTC_FLAG_TAMP1 | RTC_FLAG_TAMP2 | RTC_FLAG_TAMP3 )
#define RTC_FLAG_INT_TAMP_3 TAMP_SR_ITAMP3F
#define RTC_FLAG_INT_TAMP_5 TAMP_SR_ITAMP5F
#define RTC_FLAG_INT_TAMP_6 TAMP_SR_ITAMP6F
#define RTC_FLAG_INT_TAMP_8 TAMP_SR_ITAMP8F
#define RTC_FLAG_INT_TAMP_ALL (RTC_FLAG_INT_TAMP3 | RTC_FLAG_INT_TAMP5 | RTC_FLAG_INT_TAMP6 | RTC_FLAG_INT_TAMP8)
/**
* @}
*/
/** @defgroup RTCEx_MonotonicCounter_Instance RTCEx Monotonic Counter Instance Definition
* @{
*/
#define RTC_MONOTONIC_COUNTER_1 0u /*!< Monotonic counter 1 */
/**
* @}
*/
/** @defgroup RTCEx_Backup_Registers RTCEx Backup Registers Definition
* @{
*/
#define RTC_BKP_NUMBER RTC_BACKUP_NB
#define RTC_BKP_DR0 0x00u
#define RTC_BKP_DR1 0x01u
#define RTC_BKP_DR2 0x02u
#define RTC_BKP_DR3 0x03u
#define RTC_BKP_DR4 0x04u
#define RTC_BKP_DR5 0x05u
#define RTC_BKP_DR6 0x06u
#define RTC_BKP_DR7 0x07u
#define RTC_BKP_DR8 0x08u
#define RTC_BKP_DR9 0x09u
#define RTC_BKP_DR10 0x0Au
#define RTC_BKP_DR11 0x0Bu
#define RTC_BKP_DR12 0x0Cu
#define RTC_BKP_DR13 0x0Du
#define RTC_BKP_DR14 0x0Eu
#define RTC_BKP_DR15 0x0Fu
#define RTC_BKP_DR16 0x10u
#define RTC_BKP_DR17 0x11u
#define RTC_BKP_DR18 0x12u
#define RTC_BKP_DR19 0x13u
/**
* @}
*/
/** @defgroup RTCEx_Binary_Mode RTC Binary Mode (32-bit free-running counter configuration).
* Warning : It Should not be confused with the Binary format @ref RTC_Input_parameter_format_definitions.
* @{
*/
#define RTC_BINARY_NONE 0x00000000u /*!< Free running BCD calendar mode (Binary mode disabled). */
#define RTC_BINARY_ONLY RTC_ICSR_BIN_0 /*!< Free running Binary mode (BCD mode disabled) */
#define RTC_BINARY_MIX RTC_ICSR_BIN_1 /*!< Free running BCD calendar and Binary mode */
/**
* @}
*/
/** @defgroup RTCEx_Binary_mix_BCDU If Binary mode is RTC_BINARY_MIX, the BCD calendar second is incremented using the SSR Least Significant Bits.
* @{
*/
#define RTC_BINARY_MIX_BCDU_0 0x00000000u /*!< The 1s BCD calendar increment is generated each time SS[7:0] = 0 */
#define RTC_BINARY_MIX_BCDU_1 (0x1UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[8:0] = 0 */
#define RTC_BINARY_MIX_BCDU_2 (0x2UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[9:0] = 0 */
#define RTC_BINARY_MIX_BCDU_3 (0x3UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[10:0] = 0 */
#define RTC_BINARY_MIX_BCDU_4 (0x4UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[11:0] = 0 */
#define RTC_BINARY_MIX_BCDU_5 (0x5UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[12:0] = 0 */
#define RTC_BINARY_MIX_BCDU_6 (0x6UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[13:0] = 0 */
#define RTC_BINARY_MIX_BCDU_7 (0x7UL << RTC_ICSR_BCDU_Pos) /*!< The 1s BCD calendar increment is generated each time SS[14:0] = 0 */
/**
* @}
*/
/** @defgroup RTCEx_Alarm_Sub_Seconds_binary_Masks_Definitions RTC Alarm Sub Seconds with binary mode Masks Definitions
* @{
*/
#define RTC_ALARMSUBSECONDBINMASK_ALL 0x00000000u /*!< All Alarm SS fields are masked.
There is no comparison on sub seconds for Alarm */
#define RTC_ALARMSUBSECONDBINMASK_SS31_1 (1UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:1] are don't care in Alarm
comparison. Only SS[0] is compared. */
#define RTC_ALARMSUBSECONDBINMASK_SS31_2 (2UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:2] are don't care in Alarm
comparison. Only SS[1:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_3 (3UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:3] are don't care in Alarm
comparison. Only SS[2:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_4 (4UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:4] are don't care in Alarm
comparison. Only SS[3:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_5 (5UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:5] are don't care in Alarm
comparison. Only SS[4:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_6 (6UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:6] are don't care in Alarm
comparison. Only SS[5:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_7 (7UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:7] are don't care in Alarm
comparison. Only SS[6:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_8 (8UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:8] are don't care in Alarm
comparison. Only SS[7:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_9 (9UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:9] are don't care in Alarm
comparison. Only SS[8:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_10 (10UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:10] are don't care in Alarm
comparison. Only SS[9:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_11 (11UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:11] are don't care in Alarm
comparison. Only SS[10:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_12 (12UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:12] are don't care in Alarm
comparison.Only SS[11:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_13 (13UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:13] are don't care in Alarm
comparison. Only SS[12:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_14 (14UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:14] are don't care in Alarm
comparison. Only SS[13:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_15 (15UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:15] are don't care in Alarm
comparison. Only SS[14:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_16 (16UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:16] are don't care in Alarm
comparison. Only SS[15:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_17 (17UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:17] are don't care in Alarm
comparison. Only SS[16:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_18 (18UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:18] are don't care in Alarm
comparison. Only SS[17:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_19 (19UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:19] are don't care in Alarm
comparison. Only SS[18:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_20 (20UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:20] are don't care in Alarm
comparison. Only SS[19:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_21 (21UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:21] are don't care in Alarm
comparison. Only SS[20:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_22 (22UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:22] are don't care in Alarm
comparison. Only SS[21:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_23 (23UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:23] are don't care in Alarm
comparison. Only SS[22:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_24 (24UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:24] are don't care in Alarm
comparison. Only SS[23:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_25 (25UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:25] are don't care in Alarm
comparison. Only SS[24:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_26 (26UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:26] are don't care in Alarm
comparison. Only SS[25:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_27 (27UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:27] are don't care in Alarm
comparison. Only SS[26:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_28 (28UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:28] are don't care in Alarm
comparison. Only SS[27:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_29 (29UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:29] are don't care in Alarm
comparison. Only SS[28:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31_30 (30UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:30] are don't care in Alarm
comparison. Only SS[29:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_SS31 (31UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31] is don't care in Alarm
comparison. Only SS[30:0] are compared */
#define RTC_ALARMSUBSECONDBINMASK_NONE (32UL << RTC_ALRMASSR_MASKSS_Pos) /*!< SS[31:0] are compared and must match to activate alarm. */
/**
* @}
*/
/** @defgroup RTCEx_Alarm_Sub_Seconds_binary_Clear_Definitions RTC Alarm Sub Seconds with binary mode auto clear Definitions
* @{
*/
#define RTC_ALARMSUBSECONDBIN_AUTOCLR_NO 0UL /*!< The synchronous Binary counter (SS[31:0] in RTC_SSR) is free-running. */
#define RTC_ALARMSUBSECONDBIN_AUTOCLR_YES RTC_ALRMASSR_SSCLR /*!< The synchronous Binary counter (SS[31:0] in RTC_SSR) is running from 0xFFFF FFFF to
RTC_ALRMABINR -> SS[31:0] value and is automatically reloaded with 0xFFFF FFFF
whenreaching RTC_ALRMABINR -> SS[31:0]. */
/**
* @}
*/
/**
* @}
*/
/* Exported macros -----------------------------------------------------------*/
/** @defgroup RTCEx_Exported_Macros RTCEx Exported Macros
* @{
*/
/** @brief Clear the specified RTC pending flag.
* @param __HANDLE__ specifies the RTC Handle.
* @param __FLAG__ specifies the flag to check.
* This parameter can be any combination of the following values:
* @arg @ref RTC_CLEAR_ITSF Clear Internal Time-stamp flag
* @arg @ref RTC_CLEAR_TSOVF Clear Time-stamp overflow flag
* @arg @ref RTC_CLEAR_TSF Clear Time-stamp flag
* @arg @ref RTC_CLEAR_WUTF Clear Wakeup timer flag
* @arg @ref RTC_CLEAR_ALRBF Clear Alarm B flag
* @arg @ref RTC_CLEAR_ALRAF Clear Alarm A flag
* @retval None
*/
#define __HAL_RTC_CLEAR_FLAG(__HANDLE__, __FLAG__) (RTC->SCR = (__FLAG__))
/** @brief Check whether the specified RTC flag is set or not.
* @param __HANDLE__ specifies the RTC Handle.
* @param __FLAG__ specifies the flag to check.
* This parameter can be any combination of the following values:
* @arg @ref RTC_FLAG_RECALPF Recalibration pending Flag
* @arg @ref RTC_FLAG_INITF Initialization flag
* @arg @ref RTC_FLAG_RSF Registers synchronization flag
* @arg @ref RTC_FLAG_INITS Initialization status flag
* @arg @ref RTC_FLAG_SHPF Shift operation pending flag
* @arg @ref RTC_FLAG_WUTWF Wakeup timer write flag
* @arg @ref RTC_FLAG_ITSF Internal Time-stamp flag
* @arg @ref RTC_FLAG_TSOVF Time-stamp overflow flag
* @arg @ref RTC_FLAG_TSF Time-stamp flag
* @arg @ref RTC_FLAG_WUTF Wakeup timer flag
* @arg @ref RTC_FLAG_ALRBF Alarm B flag
* @arg @ref RTC_FLAG_ALRAF Alarm A flag
* @retval None
*/
#define __HAL_RTC_GET_FLAG(__HANDLE__, __FLAG__) (((((__FLAG__)) >> 8U) == 1U) ? (RTC->ICSR & (1U << (((uint16_t)(__FLAG__)) & RTC_FLAG_MASK))) : \
(RTC->SR & (1U << (((uint16_t)(__FLAG__)) & RTC_FLAG_MASK))))
/* ---------------------------------WAKEUPTIMER---------------------------------*/
/** @defgroup RTCEx_WakeUp_Timer RTC WakeUp Timer
* @{
*/
/**
* @brief Enable the RTC WakeUp Timer peripheral.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_WUTE))
/**
* @brief Disable the RTC WakeUp Timer peripheral.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_WUTE))
/**
* @brief Enable the RTC WakeUpTimer interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC WakeUpTimer interrupt sources to be enabled.
* This parameter can be:
* @arg @ref RTC_IT_WUT WakeUpTimer interrupt
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_ENABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR |= (__INTERRUPT__))
/**
* @brief Disable the RTC WakeUpTimer interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC WakeUpTimer interrupt sources to be disabled.
* This parameter can be:
* @arg @ref RTC_IT_WUT WakeUpTimer interrupt
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_DISABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR &= ~(__INTERRUPT__))
/**
* @brief Check whether the specified RTC WakeUpTimer interrupt has occurred or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC WakeUpTimer interrupt to check.
* This parameter can be:
* @arg @ref RTC_IT_WUT WakeUpTimer interrupt
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_GET_IT(__HANDLE__, __INTERRUPT__) ((((RTC->MISR) & ((__INTERRUPT__)>> 12U)) != 0UL) ? 1UL : 0UL)
/**
* @brief Check whether the specified RTC Wake Up timer interrupt has been enabled or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Wake Up timer interrupt sources to check.
* This parameter can be:
* @arg @ref RTC_IT_WUT WakeUpTimer interrupt
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((RTC->CR) & (__INTERRUPT__)) != 0UL) ? 1UL : 0UL)
/**
* @brief Get the selected RTC WakeUpTimers flag status.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC WakeUpTimer Flag is pending or not.
* This parameter can be:
* @arg @ref RTC_FLAG_WUTF
* @arg @ref RTC_FLAG_WUTWF
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__), (__FLAG__)))
/**
* @brief Clear the RTC Wake Up timers pending flags.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC WakeUpTimer Flag to clear.
* This parameter can be:
* @arg @ref RTC_FLAG_WUTF
* @retval None
*/
#define __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), RTC_CLEAR_WUTF))
/* WAKE-UP TIMER EXTI */
/* ------------------ */
#if defined(CORE_CM0PLUS)
#define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT)
#define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT))
#define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT)
#define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT))
#else
#define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT)
#define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT))
#define __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_WAKEUPTIMER_EVENT)
#define __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_WAKEUPTIMER_EVENT))
#endif
/**
* @}
*/
/* ---------------------------------TIMESTAMP---------------------------------*/
/** @defgroup RTCEx_Timestamp RTC Timestamp
* @{
*/
/**
* @brief Enable the RTC TimeStamp peripheral.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_TSE))
/**
* @brief Disable the RTC TimeStamp peripheral.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_TSE))
/**
* @brief Enable the RTC TimeStamp interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC TimeStamp interrupt source to be enabled.
* This parameter can be:
* @arg @ref RTC_IT_TS TimeStamp interrupt
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_ENABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR |= (__INTERRUPT__))
/**
* @brief Disable the RTC TimeStamp interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC TimeStamp interrupt source to be disabled.
* This parameter can be:
* @arg @ref RTC_IT_TS TimeStamp interrupt
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_DISABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR &= ~(__INTERRUPT__))
/**
* @brief Check whether the specified RTC TimeStamp interrupt has occurred or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC TimeStamp interrupt to check.
* This parameter can be:
* @arg @ref RTC_IT_TS TimeStamp interrupt
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_GET_IT(__HANDLE__, __INTERRUPT__) ((((RTC->MISR) & ((__INTERRUPT__)>> 12U)) != 0U) ? 1UL : 0UL)
/**
* @brief Check whether the specified RTC Time Stamp interrupt has been enabled or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Time Stamp interrupt source to check.
* This parameter can be:
* @arg @ref RTC_IT_TS TimeStamp interrupt
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((RTC->CR) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
/**
* @brief Get the selected RTC TimeStamps flag status.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC TimeStamp Flag is pending or not.
* This parameter can be:
* @arg @ref RTC_FLAG_TSF
* @arg @ref RTC_FLAG_TSOVF
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__),(__FLAG__)))
/**
* @brief Clear the RTC Time Stamps pending flags.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC TimeStamp Flag to clear.
* This parameter can be:
* @arg @ref RTC_FLAG_TSF
* @arg @ref RTC_FLAG_TSOVF
* @retval None
*/
#define __HAL_RTC_TIMESTAMP_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), (__FLAG__)))
/* TIMESTAMP EXTI */
/* -------------- */
#if defined(CORE_CM0PLUS)
#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
#else
#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
#endif
/**
* @brief Enable the RTC internal TimeStamp peripheral.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_INTERNAL_TIMESTAMP_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_ITSE))
/**
* @brief Disable the RTC internal TimeStamp peripheral.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_INTERNAL_TIMESTAMP_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_ITSE))
/**
* @brief Get the selected RTC Internal Time Stamps flag status.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC Internal Time Stamp Flag is pending or not.
* This parameter can be:
* @arg @ref RTC_FLAG_ITSF
* @retval None
*/
#define __HAL_RTC_INTERNAL_TIMESTAMP_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__),(__FLAG__)))
/**
* @brief Clear the RTC Internal Time Stamps pending flags.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC Internal Time Stamp Flag source to clear.
* This parameter can be:
* @arg @ref RTC_FLAG_ITSF
* @retval None
*/
#define __HAL_RTC_INTERNAL_TIMESTAMP_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), RTC_CLEAR_ITSF))
/**
* @brief Enable the RTC TimeStamp on Tamper detection.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_TAMPTS_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_TAMPTS))
/**
* @brief Disable the RTC TimeStamp on Tamper detection.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_TAMPTS_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_TAMPTS))
/**
* @brief Enable the RTC Tamper detection output.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_TAMPOE_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_TAMPOE))
/**
* @brief Disable the RTC Tamper detection output.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_TAMPOE_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_TAMPOE))
/**
* @}
*/
/* ------------------------------Calibration----------------------------------*/
/** @defgroup RTCEx_Calibration RTC Calibration
* @{
*/
/**
* @brief Enable the RTC calibration output.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_CALIBRATION_OUTPUT_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_COE))
/**
* @brief Disable the calibration output.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_CALIBRATION_OUTPUT_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_COE))
/**
* @brief Enable the clock reference detection.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_CLOCKREF_DETECTION_ENABLE(__HANDLE__) (RTC->CR |= (RTC_CR_REFCKON))
/**
* @brief Disable the clock reference detection.
* @param __HANDLE__ specifies the RTC handle.
* @retval None
*/
#define __HAL_RTC_CLOCKREF_DETECTION_DISABLE(__HANDLE__) (RTC->CR &= ~(RTC_CR_REFCKON))
/**
* @brief Get the selected RTC shift operations flag status.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC shift operation Flag is pending or not.
* This parameter can be:
* @arg @ref RTC_FLAG_SHPF
* @retval None
*/
#define __HAL_RTC_SHIFT_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__), (__FLAG__)))
/**
* @}
*/
/* ------------------------------Tamper----------------------------------*/
/** @defgroup RTCEx_Tamper RTCEx tamper
* @{
*/
/**
* @brief Enable the TAMP Tamper input detection.
* @param __HANDLE__ specifies the RTC handle.
* @param __TAMPER__ specifies the RTC Tamper source to be enabled.
* This parameter can be any combination of the following values:
* @arg RTC_TAMPER_ALL: All tampers
* @arg RTC_TAMPER_1: Tamper1
* @arg RTC_TAMPER_2: Tamper2
* @arg RTC_TAMPER_3: Tamper3
* @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
* @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_ENABLE(__HANDLE__, __TAMPER__) (TAMP->CR1 |= (__TAMPER__))
/**
* @brief Disable the TAMP Tamper input detection.
* @param __HANDLE__ specifies the RTC handle.
* @param __TAMPER__ specifies the RTC Tamper sources to be enabled.
* This parameter can be any combination of the following values:
* @arg RTC_TAMPER_ALL: All tampers
* @arg RTC_TAMPER_1: Tamper1
* @arg RTC_TAMPER_2: Tamper2
* @arg RTC_TAMPER_3: Tamper3
* @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
* @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
*/
#define __HAL_RTC_TAMPER_DISABLE(__HANDLE__, __TAMPER__) (TAMP->CR1 &= ~(__TAMPER__))
/**************************************************************************************************/
/**
* @brief Enable the TAMP Tamper interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Tamper interrupt sources to be enabled.
* This parameter can be any combination of the following values:
* @arg RTC_IT_TAMP_ALL: All tampers interrupts
* @arg RTC_IT_TAMP_1: Tamper1 interrupt
* @arg RTC_IT_TAMP_2: Tamper2 interrupt
* @arg RTC_IT_TAMP_3: Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
* @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_ENABLE_IT(__HANDLE__, __INTERRUPT__) (TAMP->IER |= (__INTERRUPT__))
/**
* @brief Disable the TAMP Tamper interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Tamper interrupt sources to be disabled.
* This parameter can be any combination of the following values:
* @arg RTC_IT_TAMP_ALL: All tampers interrupts
* @arg RTC_IT_TAMP_1: Tamper1 interrupt
* @arg RTC_IT_TAMP_2: Tamper2 interrupt
* @arg RTC_IT_TAMP_3: Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
* @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_DISABLE_IT(__HANDLE__, __INTERRUPT__) (TAMP->IER &= ~(__INTERRUPT__))
/**************************************************************************************************/
/**
* @brief Check whether the specified RTC Tamper interrupt has occurred or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Tamper interrupt to check.
* This parameter can be:
* @arg RTC_IT_TAMP_ALL: All tampers interrupts
* @arg RTC_IT_TAMP_1: Tamper1 interrupt
* @arg RTC_IT_TAMP_2: Tamper2 interrupt
* @arg RTC_IT_TAMP_3: Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
* @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_GET_IT(__HANDLE__, __INTERRUPT__) ((((TAMP->MISR) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
/**
* @brief Check whether the specified RTC Tamper interrupt has been enabled or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Tamper interrupt source to check.
* This parameter can be:
* @arg RTC_IT_TAMP_ALL: All tampers interrupts
* @arg RTC_IT_TAMP_1: Tamper1 interrupt
* @arg RTC_IT_TAMP_2: Tamper2 interrupt
* @arg RTC_IT_TAMP_3: Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_ALL: All internal tampers interrupts
* @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((TAMP->IER) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
/**
* @brief Get the selected RTC Tampers flag status.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC Tamper Flag is pending or not.
* This parameter can be:
* @arg RTC_FLAG_TAMP_1: Tamper1 flag
* @arg RTC_FLAG_TAMP_2: Tamper2 flag
* @arg RTC_FLAG_TAMP_3: Tamper3 flag
* @arg RTC_FLAG_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_FLAG_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_FLAG_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_FLAG_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_GET_FLAG(__HANDLE__, __FLAG__) ((((TAMP->SR) & (__FLAG__)) != 0U) ? 1UL : 0UL)
/**
* @brief Clear the RTC Tamper's pending flags.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC Tamper Flag to clear.
* This parameter can be:
* @arg RTC_FLAG_TAMP_ALL: All tampers flag
* @arg RTC_FLAG_TAMP_1: Tamper1 flag
* @arg RTC_FLAG_TAMP_2: Tamper2 flag
* @arg RTC_FLAG_TAMP_3: Tamper3 flag
* @arg RTC_FLAG_INT_TAMP_ALL: All Internal Tamper flags
* @arg RTC_FLAG_INT_TAMP_3: Internal Tamper3 interrupt
* @arg RTC_FLAG_INT_TAMP_5: Internal Tamper5 interrupt
* @arg RTC_FLAG_INT_TAMP_6: Internal Tamper6 interrupt
* @arg RTC_FLAG_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
#define __HAL_RTC_TAMPER_CLEAR_FLAG(__HANDLE__, __FLAG__) (((TAMP->SCR) = (__FLAG__)))
/* TAMPER EXTI */
/* ----------- */
#if defined(CORE_CM0PLUS)
#define __HAL_RTC_TAMPER_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
#define __HAL_RTC_TAMPER_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
#define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
#define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
#else
#define __HAL_RTC_TAMPER_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
#define __HAL_RTC_TAMPER_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
#define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
#define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
#endif
/**
* @}
*/
/* --------------------------------- SSR Underflow ---------------------------------*/
/** @defgroup RTCEx_SSR_Underflow RTC SSR Underflow
* @{
*/
/**
* @brief Enable the RTC SSRU interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC SSRU interrupt sources to be enabled.
* This parameter can be:
* @arg @ref RTC_IT_SSRU SSRU interrupt
* @retval None
*/
#define __HAL_RTC_SSRU_ENABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR |= (__INTERRUPT__))
/**
* @brief Disable the RTC SSRU interrupt.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC SSRU interrupt sources to be disabled.
* This parameter can be:
* @arg @ref RTC_IT_SSRU SSRU interrupt
* @retval None
*/
#define __HAL_RTC_SSRU_DISABLE_IT(__HANDLE__, __INTERRUPT__) (RTC->CR &= ~(__INTERRUPT__))
/**
* @brief Check whether the specified RTC SSRU interrupt has occurred or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC SSRU interrupt to check.
* This parameter can be:
* @arg @ref RTC_IT_SSRU SSRU interrupt
* @retval None
*/
#define __HAL_RTC_SSRU_GET_IT(__HANDLE__, __INTERRUPT__) (((RTC->MISR) & ((__INTERRUPT__) >> 1) != 0U) ? 1U : 0U)
/**
* @brief Check whether the specified RTC Wake Up timer interrupt has been enabled or not.
* @param __HANDLE__ specifies the RTC handle.
* @param __INTERRUPT__ specifies the RTC Wake Up timer interrupt sources to check.
* This parameter can be:
* @arg @ref RTC_IT_SSRU SSRU interrupt
* @retval None
*/
#define __HAL_RTC_SSRU_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((RTC->CR) & (__INTERRUPT__)) != 0U) ? 1U : 0U)
/**
* @brief Get the selected RTC SSRU's flag status.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC SSRU Flag is pending or not.
* This parameter can be:
* @arg @ref RTC_FLAG_SSRUF
* @retval None
*/
#define __HAL_RTC_SSRU_GET_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_GET_FLAG((__HANDLE__), (__FLAG__)))
/**
* @brief Clear the RTC Wake Up timer's pending flags.
* @param __HANDLE__ specifies the RTC handle.
* @param __FLAG__ specifies the RTC SSRU Flag to clear.
* This parameter can be:
* @arg @ref RTC_FLAG_SSRUF
* @retval None
*/
#define __HAL_RTC_SSRU_CLEAR_FLAG(__HANDLE__, __FLAG__) (__HAL_RTC_CLEAR_FLAG((__HANDLE__), RTC_CLEAR_SSRUF))
/* SSR Underflow EXTI */
/* ------------------ */
#if defined(CORE_CM0PLUS)
#define __HAL_RTC_SSRU_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_SSRU_EVENT)
#define __HAL_RTC_SSRU_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT))
#define __HAL_RTC_SSRU_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_SSRU_EVENT)
#define __HAL_RTC_SSRU_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT))
#else
#define __HAL_RTC_SSRU_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_SSRU_EVENT)
#define __HAL_RTC_SSRU_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT))
#define __HAL_RTC_SSRU_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_SSRU_EVENT)
#define __HAL_RTC_SSRU_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_SSRU_EVENT))
#endif
/**
* @}
*/
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup RTCEx_Exported_Functions RTCEx Exported Functions
* @{
*/
/* RTC TimeStamp functions *****************************************/
/** @defgroup RTCEx_Exported_Functions_Group1 Extended RTC TimeStamp functions
* @{
*/
HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin);
HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin);
HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_SetInternalTimeStamp(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTimeStamp(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTimeStamp, RTC_DateTypeDef *sTimeStampDate, uint32_t Format);
void HAL_RTCEx_TimeStampIRQHandler(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout);
void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc);
/**
* @}
*/
/* RTC Wake-up functions ******************************************************/
/** @defgroup RTCEx_Exported_Functions_Group2 Extended RTC Wake-up functions
* @{
*/
HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock);
HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock, uint32_t WakeUpAutoClr);
HAL_StatusTypeDef HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc);
uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout);
/**
* @}
*/
/* Extended Control functions ************************************************/
/** @defgroup RTCEx_Exported_Functions_Group3 Extended Peripheral Control functions
* @{
*/
HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef *hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue);
HAL_StatusTypeDef HAL_RTCEx_SetLowPowerCalib(RTC_HandleTypeDef *hrtc, uint32_t LowPowerCalib);
HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef *hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS);
HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef *hrtc, uint32_t CalibOutput);
HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterIncrement(RTC_HandleTypeDef *hrtc, uint32_t Instance);
HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterGet(RTC_HandleTypeDef *hrtc, uint32_t Instance, uint32_t *Value);
HAL_StatusTypeDef HAL_RTCEx_SetSSRU_IT(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_DeactivateSSRU(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_SSRUIRQHandler(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_SSRUEventCallback(RTC_HandleTypeDef *hrtc);
/**
* @}
*/
/* Extended RTC features functions *******************************************/
/** @defgroup RTCEx_Exported_Functions_Group4 Extended features functions
* @{
*/
void HAL_RTCEx_AlarmBEventCallback(RTC_HandleTypeDef *hrtc);
HAL_StatusTypeDef HAL_RTCEx_PollForAlarmBEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout);
/**
* @}
*/
/** @defgroup RTCEx_Exported_Functions_Group5 Extended RTC Tamper functions
* @{
*/
HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef *sTamper);
HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef *sTamper);
HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef *hrtc, uint32_t Tamper);
HAL_StatusTypeDef HAL_RTCEx_PollForTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t Tamper, uint32_t Timeout);
HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper);
HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper_IT(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper);
HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTamper(RTC_HandleTypeDef *hrtc, uint32_t IntTamper);
HAL_StatusTypeDef HAL_RTCEx_PollForInternalTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t IntTamper, uint32_t Timeout);
void HAL_RTCEx_TamperIRQHandler(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_InternalTamper3EventCallback(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_InternalTamper5EventCallback(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_InternalTamper6EventCallback(RTC_HandleTypeDef *hrtc);
void HAL_RTCEx_InternalTamper8EventCallback(RTC_HandleTypeDef *hrtc);
/**
* @}
*/
/** @defgroup RTCEx_Exported_Functions_Group6 Extended RTC Backup register functions
* @{
*/
void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister, uint32_t Data);
uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup RTCEx_Private_Constants RTCEx Private Constants
* @{
*/
/*#define RTC_EXTI_LINE_ALARM_EVENT EXTI_IMR1_IM17 */ /*!< External interrupt line 17 Connected to the RTC Alarm event (defined in rtc.h) */
#define RTC_EXTI_LINE_SSRU_EVENT EXTI_IMR1_IM18 /*!< External interrupt line 18 Connected to the RTC SSR Underflow event */
#define RTC_EXTI_LINE_TIMESTAMP_EVENT EXTI_IMR1_IM19 /*!< External interrupt line 19 Connected to the RTC Time Stamp events */
#define RTC_EXTI_LINE_WAKEUPTIMER_EVENT EXTI_IMR1_IM20 /*!< External interrupt line 20 Connected to the RTC Wakeup event */
#define RTC_EXTI_LINE_TAMPER_EVENT EXTI_IMR1_IM19 /*!< External interrupt line 19 Connected to the RTC tamper events */
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup RTCEx_Private_Macros RTCEx Private Macros
* @{
*/
/** @defgroup RTCEx_IS_RTC_Definitions Private macros to check input parameters
* @{
*/
#define IS_TIMESTAMP_EDGE(EDGE) (((EDGE) == RTC_TIMESTAMPEDGE_RISING) || \
((EDGE) == RTC_TIMESTAMPEDGE_FALLING))
#define IS_RTC_TIMESTAMP_PIN(PIN) (((PIN) == RTC_TIMESTAMPPIN_DEFAULT))
#define IS_RTC_TIMESTAMPONTAMPER_DETECTION(DETECTION) (((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_ENABLE) || \
((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_DISABLE))
#define IS_RTC_TAMPER_TAMPERDETECTIONOUTPUT(MODE) (((MODE) == RTC_TAMPERDETECTIONOUTPUT_ENABLE) || \
((MODE) == RTC_TAMPERDETECTIONOUTPUT_DISABLE))
#define IS_RTC_WAKEUP_CLOCK(CLOCK) (((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV16) || \
((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV8) || \
((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV4) || \
((CLOCK) == RTC_WAKEUPCLOCK_RTCCLK_DIV2) || \
((CLOCK) == RTC_WAKEUPCLOCK_CK_SPRE_16BITS) || \
((CLOCK) == RTC_WAKEUPCLOCK_CK_SPRE_17BITS))
#define IS_RTC_WAKEUP_COUNTER(COUNTER) ((COUNTER) <= RTC_WUTR_WUT)
#define IS_RTC_SMOOTH_CALIB_PERIOD(PERIOD) (((PERIOD) == RTC_SMOOTHCALIB_PERIOD_32SEC) || \
((PERIOD) == RTC_SMOOTHCALIB_PERIOD_16SEC) || \
((PERIOD) == RTC_SMOOTHCALIB_PERIOD_8SEC))
#define IS_RTC_SMOOTH_CALIB_PLUS(PLUS) (((PLUS) == RTC_SMOOTHCALIB_PLUSPULSES_SET) || \
((PLUS) == RTC_SMOOTHCALIB_PLUSPULSES_RESET))
#define IS_RTC_SMOOTH_CALIB_MINUS(VALUE) ((VALUE) <= RTC_CALR_CALM)
#define IS_RTC_LOW_POWER_CALIB(LPCAL) (((LPCAL) == RTC_LPCAL_SET) || \
((LPCAL) == RTC_LPCAL_RESET))
#define IS_RTC_TAMPER(__TAMPER__) ((((__TAMPER__) & RTC_TAMPER_ALL) != 0x00U) && \
(((__TAMPER__) & ~RTC_TAMPER_ALL) == 0x00U))
#define IS_RTC_INTERNAL_TAMPER(__INT_TAMPER__) ((((__INT_TAMPER__) & RTC_INT_TAMPER_ALL) != 0x00U) && \
(((__INT_TAMPER__) & ~RTC_INT_TAMPER_ALL) == 0x00U))
#define IS_RTC_TAMPER_TRIGGER(__TRIGGER__) (((__TRIGGER__) == RTC_TAMPERTRIGGER_RISINGEDGE) || \
((__TRIGGER__) == RTC_TAMPERTRIGGER_FALLINGEDGE) || \
((__TRIGGER__) == RTC_TAMPERTRIGGER_LOWLEVEL) || \
((__TRIGGER__) == RTC_TAMPERTRIGGER_HIGHLEVEL))
#define IS_RTC_TAMPER_ERASE_MODE(__MODE__) (((__MODE__) == RTC_TAMPER_ERASE_BACKUP_ENABLE) || \
((__MODE__) == RTC_TAMPER_ERASE_BACKUP_DISABLE))
#define IS_RTC_TAMPER_MASKFLAG_STATE(__STATE__) (((__STATE__) == RTC_TAMPERMASK_FLAG_ENABLE) || \
((__STATE__) == RTC_TAMPERMASK_FLAG_DISABLE))
#define IS_RTC_TAMPER_FILTER(__FILTER__) (((__FILTER__) == RTC_TAMPERFILTER_DISABLE) || \
((__FILTER__) == RTC_TAMPERFILTER_2SAMPLE) || \
((__FILTER__) == RTC_TAMPERFILTER_4SAMPLE) || \
((__FILTER__) == RTC_TAMPERFILTER_8SAMPLE))
#define IS_RTC_TAMPER_SAMPLING_FREQ(__FREQ__) (((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV32768)|| \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV16384)|| \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV8192) || \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV4096) || \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV2048) || \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV1024) || \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV512) || \
((__FREQ__) == RTC_TAMPERSAMPLINGFREQ_RTCCLK_DIV256))
#define IS_RTC_TAMPER_PRECHARGE_DURATION(__DURATION__) (((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_1RTCCLK) || \
((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_2RTCCLK) || \
((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_4RTCCLK) || \
((__DURATION__) == RTC_TAMPERPRECHARGEDURATION_8RTCCLK))
#define IS_RTC_TAMPER_PULLUP_STATE(__STATE__) (((__STATE__) == RTC_TAMPER_PULLUP_ENABLE) || \
((__STATE__) == RTC_TAMPER_PULLUP_DISABLE))
#define IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(DETECTION) (((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_ENABLE) || \
((DETECTION) == RTC_TIMESTAMPONTAMPERDETECTION_DISABLE))
#define IS_RTC_BKP(__BKP__) ((__BKP__) < RTC_BKP_NUMBER)
#define IS_RTC_SHIFT_ADD1S(SEL) (((SEL) == RTC_SHIFTADD1S_RESET) || \
((SEL) == RTC_SHIFTADD1S_SET))
#define IS_RTC_SHIFT_SUBFS(FS) ((FS) <= RTC_SHIFTR_SUBFS)
#define IS_RTC_CALIB_OUTPUT(OUTPUT) (((OUTPUT) == RTC_CALIBOUTPUT_512HZ) || \
((OUTPUT) == RTC_CALIBOUTPUT_1HZ))
#define IS_RTC_BINARY_MODE(MODE) (((MODE) == RTC_BINARY_NONE) || \
((MODE) == RTC_BINARY_ONLY) || \
((MODE) == RTC_BINARY_MIX ))
#define IS_RTC_BINARY_MIX_BCDU(BDCU) (((BDCU) == RTC_BINARY_MIX_BCDU_0) || \
((BDCU) == RTC_BINARY_MIX_BCDU_1) || \
((BDCU) == RTC_BINARY_MIX_BCDU_2) || \
((BDCU) == RTC_BINARY_MIX_BCDU_3) || \
((BDCU) == RTC_BINARY_MIX_BCDU_4) || \
((BDCU) == RTC_BINARY_MIX_BCDU_5) || \
((BDCU) == RTC_BINARY_MIX_BCDU_6) || \
((BDCU) == RTC_BINARY_MIX_BCDU_7))
#define IS_RTC_ALARM_SUB_SECOND_BINARY_MASK(MASK) (((MASK) == 0u) || \
(((MASK) >= RTC_ALARMSUBSECONDBINMASK_SS31_1) && ((MASK) <= RTC_ALARMSUBSECONDBINMASK_NONE)))
#define IS_RTC_ALARMSUBSECONDBIN_AUTOCLR(SEL) (((SEL) == RTC_ALARMSUBSECONDBIN_AUTOCLR_NO) || \
((SEL) == RTC_ALARMSUBSECONDBIN_AUTOCLR_YES))
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32WLxx_HAL_RTC_EX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/