/* mbed Microcontroller Library * SPDX-License-Identifier: BSD-3-Clause ****************************************************************************** * * Copyright (c) 2016-2020 STMicroelectronics. * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the * License. You may obtain a copy of the License at: * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ #include "mbed_assert.h" #include "analogin_api.h" #if DEVICE_ANALOGIN #include "mbed_wait_api.h" #include "cmsis.h" #include "pinmap.h" #include "mbed_error.h" #include "PeripheralPins.h" #if STATIC_PINMAP_READY #define ANALOGIN_INIT_DIRECT analogin_init_direct void analogin_init_direct(analogin_t *obj, const PinMap *pinmap) #else #define ANALOGIN_INIT_DIRECT _analogin_init_direct static void _analogin_init_direct(analogin_t *obj, const PinMap *pinmap) #endif { uint32_t function = (uint32_t)pinmap->function; // Get the peripheral name from the pin and assign it to the object obj->handle.Instance = (ADC_TypeDef *)pinmap->peripheral; // ADC Internal Channels "pins" (Temperature, Vref, Vbat, ...) // are described in PinNames.h and PeripheralPins.c // Pin value must be between 0xF0 and 0xFF if ((pinmap->pin < 0xF0) || (pinmap->pin >= 0x100)) { // Normal channels // Configure GPIO pin_function(pinmap->pin, pinmap->function); pin_mode(pinmap->pin, PullNone); } else { // Internal channels // No GPIO configuration for internal channels } MBED_ASSERT(obj->handle.Instance != (ADC_TypeDef *)NC); MBED_ASSERT(function != (uint32_t)NC); obj->channel = STM_PIN_CHANNEL(function); // Save pin number for the read function obj->pin = pinmap->pin; // Configure ADC object structures obj->handle.State = HAL_ADC_STATE_RESET; obj->handle.Init.OversamplingMode = DISABLE; obj->handle.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV1; obj->handle.Init.Resolution = ADC_RESOLUTION_12B; obj->handle.Init.SamplingTime = ADC_SAMPLETIME_160CYCLES_5; obj->handle.Init.ScanConvMode = ADC_SCAN_DIRECTION_FORWARD; obj->handle.Init.DataAlign = ADC_DATAALIGN_RIGHT; obj->handle.Init.ContinuousConvMode = DISABLE; obj->handle.Init.DiscontinuousConvMode = DISABLE; obj->handle.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIG_EDGE_NONE; obj->handle.Init.ExternalTrigConv = ADC_EXTERNALTRIG0_T6_TRGO; // Not used here obj->handle.Init.DMAContinuousRequests = DISABLE; obj->handle.Init.EOCSelection = EOC_SINGLE_CONV; obj->handle.Init.Overrun = OVR_DATA_OVERWRITTEN; obj->handle.Init.LowPowerAutoWait = ENABLE; obj->handle.Init.LowPowerFrequencyMode = DISABLE; // To be enabled only if ADC clock < 2.8 MHz obj->handle.Init.LowPowerAutoPowerOff = DISABLE; __HAL_RCC_ADC1_CLK_ENABLE(); if (HAL_ADC_Init(&obj->handle) != HAL_OK) { error("Cannot initialize ADC"); } if (!HAL_ADCEx_Calibration_GetValue(&obj->handle, ADC_SINGLE_ENDED)) { HAL_ADCEx_Calibration_Start(&obj->handle, ADC_SINGLE_ENDED); } __HAL_ADC_ENABLE(&obj->handle); } void analogin_init(analogin_t *obj, PinName pin) { int peripheral; int function; if ((pin < 0xF0) || (pin >= 0x100)) { peripheral = (int)pinmap_peripheral(pin, PinMap_ADC); function = (int)pinmap_find_function(pin, PinMap_ADC); } else { peripheral = (int)pinmap_peripheral(pin, PinMap_ADC_Internal); function = (int)pinmap_find_function(pin, PinMap_ADC_Internal); } const PinMap static_pinmap = {pin, peripheral, function}; ANALOGIN_INIT_DIRECT(obj, &static_pinmap); } uint16_t adc_read(analogin_t *obj) { ADC_ChannelConfTypeDef sConfig = {0}; // Configure ADC channel sConfig.Rank = ADC_RANK_CHANNEL_NUMBER; switch (obj->channel) { case 0: sConfig.Channel = ADC_CHANNEL_0; break; case 1: sConfig.Channel = ADC_CHANNEL_1; break; case 2: sConfig.Channel = ADC_CHANNEL_2; break; case 3: sConfig.Channel = ADC_CHANNEL_3; break; case 4: sConfig.Channel = ADC_CHANNEL_4; break; case 5: sConfig.Channel = ADC_CHANNEL_5; break; case 6: sConfig.Channel = ADC_CHANNEL_6; break; case 7: sConfig.Channel = ADC_CHANNEL_7; break; case 8: sConfig.Channel = ADC_CHANNEL_8; break; case 9: sConfig.Channel = ADC_CHANNEL_9; break; case 10: sConfig.Channel = ADC_CHANNEL_10; break; case 11: sConfig.Channel = ADC_CHANNEL_11; break; case 12: sConfig.Channel = ADC_CHANNEL_12; break; case 13: sConfig.Channel = ADC_CHANNEL_13; break; case 14: sConfig.Channel = ADC_CHANNEL_14; break; case 15: sConfig.Channel = ADC_CHANNEL_15; break; #ifdef ADC_CHANNEL_VLCD case 16: sConfig.Channel = ADC_CHANNEL_VLCD; break; #endif case 17: sConfig.Channel = ADC_CHANNEL_VREFINT; break; case 18: sConfig.Channel = ADC_CHANNEL_TEMPSENSOR; break; default: return 0; } /* Reset ADC channel selection register */ ADC1->CHSELR = 0; HAL_ADC_ConfigChannel(&obj->handle, &sConfig); HAL_ADC_Start(&obj->handle); // Start conversion // Wait end of conversion and get value uint16_t adcValue = 0; if (HAL_ADC_PollForConversion(&obj->handle, 10) == HAL_OK) { adcValue = (uint16_t)HAL_ADC_GetValue(&obj->handle); } LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE((&obj->handle)->Instance), LL_ADC_PATH_INTERNAL_NONE); return adcValue; } const PinMap *analogin_pinmap() { return PinMap_ADC; } #endif