GitBucket
Newer
/**
******************************************************************************
* @file stm32g0xx_hal_tim_ex.h
* @author MCD Application Team
* @brief Header file of TIM HAL Extended module.
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2018 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32G0xx_HAL_TIM_EX_H
#define STM32G0xx_HAL_TIM_EX_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32g0xx_hal_def.h"
/** @addtogroup STM32G0xx_HAL_Driver
* @{
*/
/** @addtogroup TIMEx
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup TIMEx_Exported_Types TIM Extended Exported Types
* @{
*/
/**
* @brief TIM Hall sensor Configuration Structure definition
*/
typedef struct
{
uint32_t IC1Polarity; /*!< Specifies the active edge of the input signal.
This parameter can be a value of @ref TIM_Input_Capture_Polarity */
uint32_t IC1Prescaler; /*!< Specifies the Input Capture Prescaler.
This parameter can be a value of @ref TIM_Input_Capture_Prescaler */
uint32_t IC1Filter; /*!< Specifies the input capture filter.
This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */
uint32_t Commutation_Delay; /*!< Specifies the pulse value to be loaded into the Capture Compare Register.
This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */
} TIM_HallSensor_InitTypeDef;
/**
* @brief TIM Break/Break2 input configuration
*/
typedef struct
{
uint32_t Source; /*!< Specifies the source of the timer break input.
This parameter can be a value of @ref TIMEx_Break_Input_Source */
uint32_t Enable; /*!< Specifies whether or not the break input source is enabled.
This parameter can be a value of @ref TIMEx_Break_Input_Source_Enable */
uint32_t Polarity; /*!< Specifies the break input source polarity.
This parameter can be a value of @ref TIMEx_Break_Input_Source_Polarity */
} TIMEx_BreakInputConfigTypeDef;
/**
* @}
*/
/* End of exported types -----------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup TIMEx_Exported_Constants TIM Extended Exported Constants
* @{
*/
/** @defgroup TIMEx_Remap TIM Extended Remapping
* @{
*/
#define TIM_TIM1_ETR_GPIO 0x00000000U /* !< TIM1_ETR is connected to GPIO */
#if defined(COMP1) && defined(COMP2)
#define TIM_TIM1_ETR_COMP1 TIM1_AF1_ETRSEL_0 /* !< TIM1_ETR is connected to COMP1 output */
#define TIM_TIM1_ETR_COMP2 TIM1_AF1_ETRSEL_1 /* !< TIM1_ETR is connected to COMP2 output */
#endif /* COMP1 && COMP2 */
#define TIM_TIM1_ETR_ADC1_AWD1 (TIM1_AF1_ETRSEL_1 | TIM1_AF1_ETRSEL_0) /* !< TIM1_ETR is connected to ADC1 AWD1 */
#define TIM_TIM1_ETR_ADC1_AWD2 TIM1_AF1_ETRSEL_2 /* !< TIM1_ETR is connected to ADC1 AWD2 */
#define TIM_TIM1_ETR_ADC1_AWD3 (TIM1_AF1_ETRSEL_2 | TIM1_AF1_ETRSEL_0) /* !< TIM1_ETR is connected to ADC1 AWD3 */
#if defined(COMP3)
#define TIM_TIM1_ETR_COMP3 (TIM1_AF1_ETRSEL_2 | TIM1_AF1_ETRSEL_1) /* !< TIM1_ETR is connected to COMP3 output */
#endif /* COMP3 */
#if defined(TIM2)
#define TIM_TIM2_ETR_GPIO 0x00000000U /* !< TIM2_ETR is connected to GPIO */
#define TIM_TIM2_ETR_COMP1 TIM2_AF1_ETRSEL_0 /* !< TIM2_ETR is connected to COMP1 output */
#define TIM_TIM2_ETR_COMP2 TIM2_AF1_ETRSEL_1 /* !< TIM2_ETR is connected to COMP2 output */
#define TIM_TIM2_ETR_LSE (TIM2_AF1_ETRSEL_1 | TIM2_AF1_ETRSEL_0) /* !< TIM2_ETR is connected to LSE */
#if defined(COMP3)
#define TIM_TIM2_ETR_MCO TIM2_AF1_ETRSEL_2 /* !< TIM2_ETR is connected to MCO */
#define TIM_TIM2_ETR_MCO2 (TIM1_AF1_ETRSEL_2 | TIM1_AF1_ETRSEL_0) /* !< TIM2_ETR is connected to MCO2 */
#define TIM_TIM2_ETR_COMP3 (TIM1_AF1_ETRSEL_2 | TIM1_AF1_ETRSEL_1) /* !< TIM2_ETR is connected to COMP3 output */
#endif /* COMP3 */
#endif /* TIM2 */
#if defined(TIM3)
#define TIM_TIM3_ETR_GPIO 0x00000000U /* !< TIM3_ETR is connected to GPIO */
#if defined(COMP1) && defined(COMP2)
#define TIM_TIM3_ETR_COMP1 TIM3_AF1_ETRSEL_0 /* !< TIM3_ETR is connected to COMP1 output */
#define TIM_TIM3_ETR_COMP2 TIM3_AF1_ETRSEL_1 /* !< TIM3_ETR is connected to COMP2 output */
#endif /* COMP1 && COMP2 */
#if defined(COMP3)
#define TIM_TIM3_ETR_COMP3 (TIM3_AF1_ETRSEL_1 | TIM3_AF1_ETRSEL_0) /* !< TIM3_ETR is connected to COMP3 output */
#endif /* COMP3 */
#endif /* TIM3 */
#if defined(TIM4)
#define TIM_TIM4_ETR_GPIO 0x00000000U /* !< TIM4_ETR is connected to GPIO */
#if defined(COMP1) && defined(COMP2)
#define TIM_TIM4_ETR_COMP1 TIM4_AF1_ETRSEL_0 /* !< TIM4_ETR is connected to COMP1 output */
#define TIM_TIM4_ETR_COMP2 TIM4_AF1_ETRSEL_1 /* !< TIM4_ETR is connected to COMP2 output */
#endif /* COMP1 && COMP2 */
#if defined(COMP3)
#define TIM_TIM4_ETR_COMP3 (TIM4_AF1_ETRSEL_1 | TIM4_AF1_ETRSEL_0) /* !< TIM4_ETR is connected to COMP3 output */
#endif /* COMP3 */
#endif /* TIM4 */
/**
* @}
*/
/** @defgroup TIMEx_Break_Input TIM Extended Break input
* @{
*/
#define TIM_BREAKINPUT_BRK 0x00000001U /*!< Timer break input */
#define TIM_BREAKINPUT_BRK2 0x00000002U /*!< Timer break2 input */
/**
* @}
*/
/** @defgroup TIMEx_Break_Input_Source TIM Extended Break input source
* @{
*/
#define TIM_BREAKINPUTSOURCE_BKIN 0x00000001U /* !< An external source (GPIO) is connected to the BKIN pin */
#if defined(COMP1) && defined(COMP2)
#define TIM_BREAKINPUTSOURCE_COMP1 0x00000002U /* !< The COMP1 output is connected to the break input */
#define TIM_BREAKINPUTSOURCE_COMP2 0x00000004U /* !< The COMP2 output is connected to the break input */
#endif /* COMP1 && COMP2 */
#if defined(COMP3)
#define TIM_BREAKINPUTSOURCE_COMP3 0x00000008U /* !< The COMP3 output is connected to the break input */
#endif /* COMP3 */
/**
* @}
*/
/** @defgroup TIMEx_Break_Input_Source_Enable TIM Extended Break input source enabling
* @{
*/
#define TIM_BREAKINPUTSOURCE_DISABLE 0x00000000U /*!< Break input source is disabled */
#define TIM_BREAKINPUTSOURCE_ENABLE 0x00000001U /*!< Break input source is enabled */
/**
* @}
*/
/** @defgroup TIMEx_Break_Input_Source_Polarity TIM Extended Break input polarity
* @{
*/
#define TIM_BREAKINPUTSOURCE_POLARITY_LOW 0x00000001U /*!< Break input source is active low */
#define TIM_BREAKINPUTSOURCE_POLARITY_HIGH 0x00000000U /*!< Break input source is active_high */
/**
* @}
*/
/** @defgroup TIMEx_Timer_Input_Selection TIM Extended Timer input selection
* @{
*/
#define TIM_TIM1_TI1_GPIO 0x00000000U /* !< TIM1_TI1 is connected to GPIO */
#if defined(COMP1)
#define TIM_TIM1_TI1_COMP1 0x00000001U /* !< TIM1_TI1 is connected to COMP1 OUT */
#endif /* COMP1 */
#define TIM_TIM1_TI2_GPIO 0x00000000U /* !< TIM1_TI2 is connected to GPIO */
#if defined(COMP2)
#define TIM_TIM1_TI2_COMP2 0x00000100U /* !< TIM1_TI2 is connected to COMP2 OUT */
#endif /* COMP2 */
#define TIM_TIM1_TI3_GPIO 0x00000000U /* !< TIM1_TI3 is connected to GPIO */
#if defined(COMP3)
#define TIM_TIM1_TI3_COMP3 0x00010000U /* !< TIM1_TI3 is connected to COMP3 OUT */
#endif /* COMP3 */
#if defined(TIM2)
#define TIM_TIM2_TI1_GPIO 0x00000000U /* !< TIM2_TI1 is connected to GPIO */
#define TIM_TIM2_TI1_COMP1 0x00000001U /* !< TIM2_TI1 is connected to COMP1 OUT */
#define TIM_TIM2_TI2_GPIO 0x00000000U /* !< TIM2_TI2 is connected to GPIO */
#define TIM_TIM2_TI2_COMP2 0x00000100U /* !< TIM2_TI2 is connected to COMP2 OUT */
#define TIM_TIM2_TI3_GPIO 0x00000000U /* !< TIM2_TI3 is connected to GPIO */
#if defined(COMP3)
#define TIM_TIM2_TI3_COMP3 0x00010000U /* !< TIM2_TI3 is connected to COMP3 OUT */
#endif /* COMP3 */
#endif /* TIM2 */
#define TIM_TIM3_TI1_GPIO 0x00000000U /* !< TIM3_TI1 is connected to GPIO */
#if defined(COMP1)
#define TIM_TIM3_TI1_COMP1 0x00000001U /* !< TIM3_TI1 is connected to COMP1 OUT */
#endif /* COMP1 */
#define TIM_TIM3_TI2_GPIO 0x00000000U /* !< TIM3_TI2 is connected to GPIO */
#if defined(COMP2)
#define TIM_TIM3_TI2_COMP2 0x00000100U /* !< TIM3_TI2 is connected to COMP2 OUT */
#endif /* COMP2 */
#define TIM_TIM3_TI3_GPIO 0x00000000U /* !< TIM3_TI3 is connected to GPIO */
#if defined(COMP3)
#define TIM_TIM3_TI3_COMP3 0x00010000U /* !< TIM3_TI3 is connected to COMP3 OUT */
#endif /* COMP3 */
#if defined(TIM4)
#define TIM_TIM4_TI1_GPIO 0x00000000U /* !< TIM4_TI1 is connected to GPIO */
#if defined(COMP1)
#define TIM_TIM4_TI1_COMP1 0x00000001U /* !< TIM4_TI1 is connected to COMP1 OUT */
#endif /* COMP1 */
#define TIM_TIM4_TI2_GPIO 0x00000000U /* !< TIM4_TI2 is connected to GPIO */
#if defined(COMP2)
#define TIM_TIM4_TI2_COMP2 0x00000100U /* !< TIM4_TI2 is connected to COMP2 OUT */
#endif /* COMP2 */
#define TIM_TIM4_TI3_GPIO 0x00000000U /* !< TIM4_TI3 is connected to GPIO */
#if defined(COMP3)
#define TIM_TIM4_TI3_COMP3 0x00010000U /* !< TIM4_TI3 is connected to COMP3 OUT */
#endif /* COMP3 */
#endif /* TIM4 */
#define TIM_TIM14_TI1_GPIO 0x00000000U /* !< TIM14_TI1 is connected to GPIO */
#define TIM_TIM14_TI1_RTC 0x00000001U /* !< TIM14_TI1 is connected to RTC clock */
#define TIM_TIM14_TI1_HSE_32 0x00000002U /* !< TIM14_TI1 is connected to HSE div 32 */
#define TIM_TIM14_TI1_MCO 0x00000003U /* !< TIM14_TI1 is connected to MCO */
#if defined(RCC_MCO2_SUPPORT)
#define TIM_TIM14_TI1_MCO2 0x00000004U /* !< TIM14_TI1 is connected to MCO2 */
#endif
#if defined(TIM15)
#define TIM_TIM15_TI1_GPIO 0x00000000U /* !< TIM15_TI1 is connected to GPIO */
#define TIM_TIM15_TI1_TIM2_CH1 0x00000001U /* !< TIM15_TI1 is connected to TIM2 CH1 */
#define TIM_TIM15_TI1_TIM3_CH1 0x00000002U /* !< TIM15_TI1 is connected to TIM3 CH1 */
#define TIM_TIM15_TI2_GPIO 0x00000000U /* !< TIM15_TI2 is connected to GPIO */
#define TIM_TIM15_TI2_TIM2_CH2 0x00000100U /* !< TIM15_TI2 is connected to TIM2 CH2 */
#define TIM_TIM15_TI2_TIM3_CH2 0x00000200U /* !< TIM15_TI2 is connected to TIM3 CH2 */
#endif /* TIM15 */
#define TIM_TIM16_TI1_GPIO 0x00000000U /* !< TIM16_TI1 is connected to GPIO */
#define TIM_TIM16_TI1_LSI 0x00000001U /* !< TIM16_TI1 is connected to LSI */
#define TIM_TIM16_TI1_LSE 0x00000002U /* !< TIM16_TI1 is connected to LSE */
#define TIM_TIM16_TI1_RTC_WAKEUP 0x00000003U /* !< TIM16_TI1 is connected to TRC wakeup interrupt */
#if defined(RCC_MCO2_SUPPORT)
#define TIM_TIM16_TI1_MCO2 0x00000004U /* !< TIM16_TI1 is connected to MCO2 */
#endif /* RCC_MCO2_SUPPORT */
#define TIM_TIM17_TI1_GPIO 0x00000000U /* !< TIM17_TI1 is connected to GPIO */
#if defined(RCC_HSI48_SUPPORT)
#define TIM_TIM17_TI1_HSI48 0x00000001U /* !< TIM17_TI1 is connected to HSI48/256 */
#endif /* RCC_HSI48_SUPPORT */
#define TIM_TIM17_TI1_HSE_32 0x00000002U /* !< TIM17_TI1 is connected to HSE div 32 */
#define TIM_TIM17_TI1_MCO 0x00000003U /* !< TIM17_TI1 is connected to MCO */
#if defined(RCC_MCO2_SUPPORT)
#define TIM_TIM17_TI1_MCO2 0x00000004U /* !< TIM17_TI1 is connected to MCO2 */
#endif /* RCC_MCO2_SUPPORT */
/**
* @}
*/
/**
* @}
*/
/* End of exported constants -------------------------------------------------*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup TIMEx_Exported_Macros TIM Extended Exported Macros
* @{
*/
/**
* @}
*/
/* End of exported macro -----------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/** @defgroup TIMEx_Private_Macros TIM Extended Private Macros
* @{
*/
#define IS_TIM_REMAP(__REMAP__) ((((__REMAP__) & 0xFFFC3FFFU) == 0x00000000U))
#define IS_TIM_BREAKINPUT(__BREAKINPUT__) (((__BREAKINPUT__) == TIM_BREAKINPUT_BRK) || \
((__BREAKINPUT__) == TIM_BREAKINPUT_BRK2))
#if defined(COMP1) && defined(COMP2) && defined(COMP3)
#define IS_TIM_BREAKINPUTSOURCE(__SOURCE__) (((__SOURCE__) == TIM_BREAKINPUTSOURCE_BKIN) || \
((__SOURCE__) == TIM_BREAKINPUTSOURCE_COMP1) || \
((__SOURCE__) == TIM_BREAKINPUTSOURCE_COMP2) || \
((__SOURCE__) == TIM_BREAKINPUTSOURCE_COMP3))
#elif defined(COMP1) && defined(COMP2)
#define IS_TIM_BREAKINPUTSOURCE(__SOURCE__) (((__SOURCE__) == TIM_BREAKINPUTSOURCE_BKIN) || \
((__SOURCE__) == TIM_BREAKINPUTSOURCE_COMP1) || \
((__SOURCE__) == TIM_BREAKINPUTSOURCE_COMP2))
#else
#define IS_TIM_BREAKINPUTSOURCE(__SOURCE__) ((__SOURCE__) == TIM_BREAKINPUTSOURCE_BKIN)
#endif /* COMP1 && COMP2 && COMP3 */
#define IS_TIM_BREAKINPUTSOURCE_STATE(__STATE__) (((__STATE__) == TIM_BREAKINPUTSOURCE_DISABLE) || \
((__STATE__) == TIM_BREAKINPUTSOURCE_ENABLE))
#define IS_TIM_BREAKINPUTSOURCE_POLARITY(__POLARITY__) (((__POLARITY__) == TIM_BREAKINPUTSOURCE_POLARITY_LOW) || \
((__POLARITY__) == TIM_BREAKINPUTSOURCE_POLARITY_HIGH))
#define IS_TIM_TISEL(__TISEL__) ((((__TISEL__) & 0xF0F0F0F0U) == 0x00000000U))
/**
* @}
*/
/* End of private macro ------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup TIMEx_Exported_Functions TIM Extended Exported Functions
* @{
*/
/** @addtogroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions
* @brief Timer Hall Sensor functions
* @{
*/
/* Timer Hall Sensor functions **********************************************/
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef *sConfig);
HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim);
void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim);
void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim);
/* Blocking mode: Polling */
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim);
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim);
/* Non-Blocking mode: Interrupt */
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim);
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim);
/* Non-Blocking mode: DMA */
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length);
HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim);
/**
* @}
*/
/** @addtogroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions
* @brief Timer Complementary Output Compare functions
* @{
*/
/* Timer Complementary Output Compare functions *****************************/
/* Blocking mode: Polling */
HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel);
HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel);
/* Non-Blocking mode: Interrupt */
HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
/* Non-Blocking mode: DMA */
HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length);
HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel);
/**
* @}
*/
/** @addtogroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions
* @brief Timer Complementary PWM functions
* @{
*/
/* Timer Complementary PWM functions ****************************************/
/* Blocking mode: Polling */
HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel);
HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel);
/* Non-Blocking mode: Interrupt */
HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
/* Non-Blocking mode: DMA */
HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length);
HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel);
/**
* @}
*/
/** @addtogroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions
* @brief Timer Complementary One Pulse functions
* @{
*/
/* Timer Complementary One Pulse functions **********************************/
/* Blocking mode: Polling */
HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
/* Non-Blocking mode: Interrupt */
HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
/**
* @}
*/
/** @addtogroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
* @brief Peripheral Control functions
* @{
*/
/* Extended Control functions ************************************************/
HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef *htim, uint32_t InputTrigger,
uint32_t CommutationSource);
HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef *htim, uint32_t InputTrigger,
uint32_t CommutationSource);
HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef *htim, uint32_t InputTrigger,
uint32_t CommutationSource);
HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
TIM_MasterConfigTypeDef *sMasterConfig);
HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim,
TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig);
HAL_StatusTypeDef HAL_TIMEx_ConfigBreakInput(TIM_HandleTypeDef *htim, uint32_t BreakInput,
TIMEx_BreakInputConfigTypeDef *sBreakInputConfig);
HAL_StatusTypeDef HAL_TIMEx_GroupChannel5(TIM_HandleTypeDef *htim, uint32_t Channels);
HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap);
HAL_StatusTypeDef HAL_TIMEx_TISelection(TIM_HandleTypeDef *htim, uint32_t TISelection, uint32_t Channel);
HAL_StatusTypeDef HAL_TIMEx_DisarmBreakInput(TIM_HandleTypeDef *htim, uint32_t BreakInput);
HAL_StatusTypeDef HAL_TIMEx_ReArmBreakInput(TIM_HandleTypeDef *htim, uint32_t BreakInput);
/**
* @}
*/
/** @addtogroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions
* @brief Extended Callbacks functions
* @{
*/
/* Extended Callback **********************************************************/
void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef *htim);
void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef *htim);
void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim);
void HAL_TIMEx_Break2Callback(TIM_HandleTypeDef *htim);
/**
* @}
*/
/** @addtogroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions
* @brief Extended Peripheral State functions
* @{
*/
/* Extended Peripheral State functions ***************************************/
HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim);
HAL_TIM_ChannelStateTypeDef HAL_TIMEx_GetChannelNState(TIM_HandleTypeDef *htim, uint32_t ChannelN);
/**
* @}
*/
/**
* @}
*/
/* End of exported functions -------------------------------------------------*/
/* Private functions----------------------------------------------------------*/
/** @addtogroup TIMEx_Private_Functions TIMEx Private Functions
* @{
*/
void TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma);
void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef *hdma);
/**
* @}
*/
/* End of private functions --------------------------------------------------*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32G0xx_HAL_TIM_EX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/