This patch enables SDEI support for all Tegra platforms, with
the following configuration settings.

* SGI 8 as the source IRQ
* Special Private Event 0
* Three private, dynamic events
* Three shared, dynamic events
* Twelve general purpose explicit events

Verified using TFTF SDEI test suite.

******************************* Summary *******************************
 Test suite 'SDEI'                                               Passed
 =================================
 Tests Skipped : 0
 Tests Passed  : 5
 Tests Failed  : 0
 Tests Crashed : 0
 Total tests   : 5
 =================================

Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I1922069931a7876a4594e53260ee09f2e4f09390

This patch enables the Exception Handling Framework to service the WDT
interrupts on all Tegra platforms.

Verified that the watchdog timer interrupt fires after migrating to
the EHF.

Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I6b2e33da7841aa064e3a8f825c26fadf168cd0d5

This patch enables on-chip timer1 interrupts for Tegra210 platforms.

Change-Id: Ic7417dc0e69264d7c28aa012fe2322cd30838f3e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra210B01 SoCs support atomic context save for the two SE
hardware engines. Tegra210 SoCs have support for only one SE
engine and support a software based save/restore mechanism
instead.

This patch updates the SE driver to make this change.

Change-Id: Ia5e5ed75d0fe011f17809684bbc2ed2338925946
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I5c2fe3b6a667acf80c808cfec4a64059a2c9c25f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Tegra210 SoCs need the sc7entry-fw to enter System Suspend mode,
but there might be certain boards that do not have this firmware
blob. To stop the NS world from issuing System suspend entry
commands on such devices, we ned to disable System Suspend from
the PSCI "features".

This patch removes the System suspend handler from the Tegra PSCI
ops, so that the framework will disable support for "System Suspend"
from the PSCI "features".

Original change by: kalyani chidambaram <kalyanic@nvidia.com>

Change-Id: Ie029f82f55990a8b3a6debb73e95e0e218bfd1f5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch sets the "secure" bit to mark the PMC hardware block
as accessible only from the secure world. This setting must be
programmed during cold boot and System Resume.

The sc7entry-fw, running on the COP, needs access to the PMC block
to enter System Suspend state, so "unlock" the PMC block before
passing control to the COP.

Change-Id: I00e39a49ae6b9f8c8eafe0cf7ff63fe6a67fdccf
Signed-off-by: kalyani chidambaram <kalyanic@nvidia.com>

This patch converts the weakly defined platform setup handlers into
actual platform specific handlers to improve code coverage numbers
and some MISRA defects.

The weakly defined handlers never get executed thus resulting in
lower coverage - function, function calls, statements, branches
and pairs.

Change-Id: I02f450f66b5754a90d934df4d76eb91459fca5f9
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch introduces the 'plat_enable_console' handler to allow
the platform to enable the right console. Tegra194 platform supports
multiple console, while all the previous platforms support only one
console.

For Tegra194 platforms, the previous bootloader checks the platform
config and sets the uart-id boot parameter, to 0xFE. On seeing this
boot parameter, the platform port uses the proper memory aperture
base address to communicate with the SPE. This functionality is
currently protected by a platform macro, ENABLE_CONSOLE_SPE.

Change-Id: I3972aa376d66bd10d868495f561dc08fe32fcb10
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Now it is needed to use the full path of the common header files.

Commit 09d40e0e0828 ("Sanitise includes across codebase") provides more
information.

Change-Id: Ifedc79d9f664d208ba565f5736612a3edd94c647
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

This patch initilises the per-CPU GIC bits during cold boot and
secondary CPU power up. Commit 80c50ee accidentally left out this
part.

Change-Id: I73ce59dbc83580a84b827cab89fe7e1f65f9f130
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Platforms that do not support bpmp firmware, do not need access
to the PMC block from outside of the CPU complex. The agents
running on the CPU can always access the PMC through the EL3
exception space.

This patch restricts non-secure world access to the PMC block on
such platforms.

Change-Id: I2c4318dc07ddf6407c1700595e0f4aac377ba258
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch uses the sc7entry-fw base/size values to calculate the
TZDRAM fence, so as to move sc7entry-fw inside the TZDRAM fence.

Change-Id: I91aeeeece857076c478cdc4c18a6ad70dc265031
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch puts all the DMA masters in reset before starting the System
Suspend sequence. This helps us make sure that there are no rogue agents
in the system trying to over-write the SC7 Entry Firmware with their own.

Change-Id: I7eb39999d229951e612fbfeb9f86c4efb8f98b5a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to enter System Suspend on Tegra210 platforms
without the traditional BPMP firmware. The BPMP firmware will no longer
be supported on Tegra210 platforms and its functionality will be
divided across the CPU and sc7entry-fw.

The sc7entry-fw takes care of performing the hardware sequence required
to enter System Suspend (SC7 power state) from the COP. The CPU is required
to load this firmware to the internal RAM of the COP and start the sequence.
The CPU also make sure that the COP is off after cold boot and is only
powered on when we want to start the actual System Suspend sequence.

The previous bootloader loads the firmware to TZDRAM and passes its base and
size as part of the boot parameters. The EL3 layer is supposed to sanitize
the parameters before touching the firmware blob.

To assist the warmboot code with the PMIC discovery, EL3 is also supposed to
program PMC's scratch register #210, with appropriate values. Without these
settings the warmboot code wont be able to get the device out of System
Suspend.

Change-Id: I5a7b868512dbfd6cfefd55acf3978a1fd7ebf1e2
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables the watchdog timer's interrupt as an FIQ
interrupt to the CPU. The interrupt generated by the watchdog
is connected to the flow controller for power management reasons,
and needs to be routed to the GICD for it to reach the CPU.

Change-Id: I9437b516da2c5d763eca72694ed7f3c7389b3d9e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables L2 error correction and parity protection
for Tegra210 on boot and exit from suspend. The previous bootloader
sets the boot parameter, indicating ECC reporting, only for B01 SKUs.

Change-Id: I6927884d375a64c69e2f1e9aed85f95c5e3cb17c
Signed-off-by: Sam Payne <spayne@nvidia.com>

This patch memmaps all the IRAM memory banks during boot. The BPMP
firmware might place the channels in any of the IRAMs, so it is better
to map all the banks to avoid surprises.

Change-Id: Ia009a65d227ee50fbb23e511ce509daf41b877ee
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds the driver to communicate with the BPMP processor
for power management use cases. BPMP controls the entry into cluster
and system power states. The Tegra210 platform port queries the BPMP
to calculate the target state for the cluster. In case BPMP does not
allow CCx entry, the core enters a power down state.

Change-Id: I9c40aef561607a0b02c49b7f8118570eb9105cc9
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds the implementation of the SE atomic context save
sequence. The atomic context-save consistently saves to the TZRAM
carveout; thus there is no need to declare context save buffer or
map MMU region in TZRAM for context save. The atomic context-save
routine is responsible to validate the context-save progress
counter, where CTX_SAVE_CNT=133(SE1)/646(SE2), and the SE error
status to ensure the context save procedure complete successfully.

Change-Id: Ic80843902af70e76415530266cb158f668976c42
Signed-off-by: Marvin Hsu <marvinh@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The platform code generates the power domain tree. The handler to
retrieve the tree should also reside in the platform code.

This patch moves the plat_get_power_domain_tree_desc() to the
individual platforms.

Change-Id: Iaafc83ed381d83129501111ef655e3c58a8a553f
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928d5b7 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a282 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca33988b9 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Commit fdb1964 ("xlat: Introduce
MAP_REGION2() macro") added a granularity field to mmap_region_t.

Tegra platforms were using the v2 xlat_tables implementation in
common/tegra_common.mk, but v1 xlat_tables.h headers in soc/*/plat_setup.c
where arrays are being defined. This caused the next physical address to
be read as granularity, causing EINVAL error and triggering an assert.

Consistently use xlat_tables_v2.h header to avoid this.

Fixes ARM-software/tf-issues#548.

Signed-off-by: Andreas Färber <afaerber@suse.de>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/

Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Tegra chips support multiple FIQ interrupt sources. These interrupts
are enabled in the GICD/GICC interfaces by the tegra_gic driver. A
new FIQ handler would be added in a subsequent change which can be
registered by the platform code.

This patch adds the GIC programming as part of the tegra_gic_setup()
which now takes an array of all the FIQ interrupts to be enabled for
the platform. The Tegra132 and Tegra210 platforms right now do not
register for any FIQ interrupts themselves, but will definitely use
this support in the future.

Change-Id: I0ea164be901cd6681167028fea0567399f18d4b8
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The BL2 fills in the UART controller ID to be used as the normal as
well as the crash console on Tegra platforms. The controller ID to
UART controller base address mapping is handled by each Tegra SoC
the base addresses might change across Tegra chips.

This patch adds the handler to parse the platform params to get the
UART ID for the per-soc handlers.

Change-Id: I4d167b20a59aaf52a31e2a8edf94d8d6f89598fa
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Replaced plat_get_syscnt_freq by plat_get_syscnt_freq2 on all
upstream platforms.

Change-Id: I3248f3f65a16dc5e9720012a05c35b9e3ba6abbe

This patch moves the definition for `plat_get_syscnt_freq()`
from arm_bl31_setup.c to arm_common.c. This could be useful
in case a delay timer needs to be installed based on the
generic timer in other BLs.
This patch also modifies the return type for this function
from `uint64_t` to `unsigned long long` within ARM and other
platform files.

Change-Id: Iccdfa811948e660d4fdcaae60ad1d700e4eda80d

This patch modifies the Tegra port to support the new platform
APIs so that we can disable the compat layer. This includes
modifications to the power management and platform topology code.

Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

T210 is the latest chip in the Tegra family of SoCs from NVIDIA. It is an
ARM v8 dual-cluster (A57/A53) SoC, with any one of the clusters being active
at a given point in time.

This patch adds support to boot the Trusted Firmware on T210 SoCs. The patch
also adds support to boot secondary CPUs, enter/exit core power states for
all CPUs in the slow/fast clusters. The support to switch between clusters
is still not available in this patch and would be available later.

Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>