Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The ATSAMA5D27-SOM1-EK1 is Microchip's evaluation kit for the SAMA5D2
System in Packages (SiPs). The ATSAMA5D27C-D1G-CU SIP embeds 128 MB
of DDR2 DRAM and the SoM has a PMIC, QSPI flash and a 100Mbps PHY.

barebox already supports the sama5d2 clocks, GPIO/Pinctrl, QSPI
controller and Ethernet MAC. Most notable omission is the sama5d2
variant of the SDHCI, which differs from the MCI used by previous AT91
boards, but we kernel boot over the network works, so lets add the board
now and have the SDHCI follow later.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

We can build multiple DTBs into the binary and board code can select
which one to use. Drop the single builtin DTB and let the boards using
it pass the correct one.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

When no PBL is used then the DTB is used in the real barebox binary. We
already have lwl-y for code which needs to be in PBL when existing and
in the real barebox binary otherwise. Do the same for the DTBs and
compile them with lwl-dtb-y.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This board is produced by Embest/Element 14 and is based on i.MX6 Dual.

For more informations on this board :
http://www.embest-tech.com/shop/star/marsboard.html

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

- switch the i.MX1 based scb9328 board to device tree
- Remove scb9328_defconfig and enable scb9328 board support in
  imx_defconfig
- Remove old environment and switch to new default environment

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add a phyCORE-i.MX 6ULL with eMMC. It has following features:
	- i.MX 6ULL Y2 792 MHz
	- 512 MB RAM
	- 4 GB eMMC
	- 10/100 MBits Ethernet
	- USB OTG
	- USB Host

Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Prepare for the new phyCORE-i.MX 6UL/ULL eMMC module by extending the
dts filenames by their boot medium. Also add the boot medium to the
compatible to be able to perform boot medium dependent setup code.

Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The phyCORE-i.MX 6Solo/DualLight is available with low-cost and
full-featured phyBOARD-Mira. One crucial difference is the supported
max. ethernet speed. On the full-featured Mira it is 1000 MBit/s but on
the low-cost Mira it is only 100 MBit/s. To cover this difference two
different images are necessary for low-cost and full-featured. Thus a
low-cost variant is added for the phyCORE-i.MX 6Solo with NAND and the
phyCORE-i.MX 6 DualLight with eMMC.

Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for Remote Modem Unit i.MX7D board.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

To prepare for addition of another ZII i.MX7D based board, i.MX7D
RMU2, rename zii-imx7d-rpu2 to zii-imx7d-dev to avoid any image naming
confusion.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for the Digi CCIMX6UL SBC Pro.
It is based on the Digi CCIMX6UL SOM with 256MB RAM and 256MB NAND
flash.

v2:
- fix includes
- rename folder to som
- switch to compressed dtb
- remove the unnecessary get_runtime_offset
all from Ahmad Fatoum

Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add the Zodiac Digital Tapping Unit, a VF610 based network device with
5 Ethernet ports.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds support for the TQ TQMLS1046a board. Currently supported:

- UART
- SD/MMC
- Network on eth3, eth2 currently not working for unknown reasons

First stage support exists but is currently untested. Serdes ports are
not yet supported.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The RDB is the Freescale LS1046a reference board. This patch adds
support for it. Currently supported:

- DDR4 RAM as read from SPD EEPROM
- UART
- SD/MMC
- RGMII network ports

The Serdes ports are currently not supported.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Barebox now has a copy of upstream DTS file for SCU4 AIB board, so
convert corresponding code to use it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for Zodiac's VF610 based SPB4 board.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds initial STMicroelectronics MP1 support along with support
for the DK2 devel board. Only very basic support:

- UART
- SDRAM memory base/size
- No 1st stage support

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The phyCORE-i.MX8M aka PCL-066 is a SoM containing a i.MX8M SoC.

phyCORE-i.MX8M:
 - 1GB LPDDR4 RAM
 - eMMC
 - microSD
 - Ethernet

Signed-off-by: Christian Hemp <christian.hemp@posteo.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Compute Module needs "no-sd" property on the MMC interface otherwise
mci-bcm2835 hangs on SD card probe.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for the following ZII i.MX8MQ based boards:

   - ZII i.MX8MQ RMB3
   - ZII i.MX8MQ Zest

Most of the basic peripherals are supported by this patch. More
advanced features such as PCIe, display support, etc, are planned to
be added later.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>