usb: Add usbroothubdes.h ...

Taken from U-Boot, needed for the upcoming dwc2 driver.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Make timeout unit clear ...

The usb_*_msg() functions take a timeout parameter. Make clear which
unit is expected by adding a _ms suffix to the variable name.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: i.MX: Use usb_register_otg_device() ...

We now have usb_register_otg_device() to register an "otg" device. Use
it and drop the custom code.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Add function to register otg dev ...

We have two drivers in the tree which register an "otg" device to
configure the host/peripheral switching. Before introducing a third
driver create a common function for it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/usb'

Merge branch 'for-next/layerscape'

usb: Change power-on / scanning timeout handling ...

Change USB port scanning procedure and timeout handling in the
following ways:

1)
The power-on delay in usb_hub_power_on() is now reduced to a value of
max(100ms, "hub->desc.bPwrOn2PwrGood * 2"). The code does not wait
using mdelay, instead usb_hub_power_on() will wait before querying
the device in the scanning loop later. The total connection timeout for
this hub, which is (1 second + hub->desc.bPwrOn2PwrGood * 2) is
calculated and will be used in the following per-port scanning loop as
the timeout to detect active USB devices on this hub.

2)
Don't delay the minimum delay (for power to stabilize) in
usb_hub_power_on(). Instead skip querying these devices in the scanning
loop usb_scan_port() until the delay time is reached.

3)
The ports are now scanned in a quasi parallel way. The current code did
wait for each (unconnected) port to reach its timeout and only then
continue with the next port. This patch now changes this to scan all
ports of all USB hubs quasi simultaneously. For this, all ports are added
to a scanning list in usb_hub_configure_ports(). The list is later scanned
in usb_device_list_scan() until all ports are ready by either a) reaching
the connection timeout (calculated earlier), or by b) detecting a USB
device. This results in a faster USB scan time as the recursive scanning
of USB hubs connected to the hub that's currently being scanned will
start earlier.

4)
Ports with overcurrent detection will get scanned multiple times if OC
condition is detected (PORT_OVERCURRENT_MAX_SCAN_COUNT).

Without patch:

    $ time usb
    usb: USB: scanning bus for devices...
    usb: 17 USB Device(s) found
    time: 10344ms

With patch:

    $ time usb
    usb: USB: scanning bus for devices...
    usb: 17 USB Device(s) found
    time: 4529ms

Delta: ~6 seconds

Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: composite: conditionally dequeue setup requests ...

This is an adoption of Kernel commit a7c12eaf2 ("usb: gadget: composite:
conditionally dequeue os_desc and setup requests"). Basically we only
want to dequeue ep0 requests when they are actually queued. Drivers like
dwc3 warn when unqueued requests are being tried to unqueued.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb/ch9.h: add USB 3.1 isoc endpoint define ...

Add a new define for USB 3.1 endpoints

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: add usb_gadget_udc_reset function ...

Add a function to notify the udc core, that a bus reset occured.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

USB: remove blackfin support ...

The blackfin architecture has been removed from barebox. Remove the
blackfin specifics in the USB drivers as well.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Drop usb_disable_asynch() ...

There are no users of usb_control_msg() in the codebase that pass
timeout of 0, so it doesn't look like usb_disable_asynch() has any
effect on USB operation. Drop that function and remove all of its uses
to simplify things.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

include/usb: Import USB_SPEED_SUPER_PLUS from Linux ...

Import USB_SPEED_SUPER_PLUS constant from Linux to support porting
kernel code that uses it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: fastboot: pass message type as enum ...

We used to pass the message type ("INFO", "FAIL", "OKAY") as strings
to fastboot_tx_print(). Change this to a enum type. This allows
fastboot_tx_print() to react on the message type in the next step.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usbgadget: autostart: add DFU support ...

Use global variable dfu_function to autostart DFU. As similar code
is used to start multifunction gadget using command, move common
code to common/usbgadget.c and consolidate it.
It turned out that '-s' option of usbgadget command does nothing,
so remove its help text and make it function as '-a'.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: fsl_udc: pass controller instance to unregister ...

ci_udc_unregister() used to unregister "the controller". Since we
may register multiple chipidea devices we called ci_udc_unregister()
for each of them. This led to messages like:

ERROR: imx-usb 53f80000.usb: gadget not registered.

Fix this by returning the registered controller. This allows us to call
ci_udc_unregister() only when we actually registered one before.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: host: ehci: do not use dev->priv ...

An ehci can be registered with ehci_register which is passed a struct
device_d *. In that case the priv pointer may already be used by the
caller, so we must not use it in the ehci code. At least for the Atmel
ehci driver this fixes a bug, here dev->priv is set two times to
different values.
Since we need dev->priv in the ehci code to get the controller in
ehci_detect() we can no longer implement that without the help of the
caller, hence we eport ehci_detect() and epect it to be called by
the code which registers a ehci host.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: host: ehci: add ehci_unregister() ...

ehci_register() allocates data and registers a ehci host. Add
ehci_unregister() to properly halt the controller and to free the memory
again.. To do so, change ehci_register() to return the ehci host rather
than an error code.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Add usb_unregister_host() ...

We have usb_register_host() which puts a new host on the list
of hosts we should also have the opposite which removes the
host from the list again.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: imx: implement support for limiting host to full speed ...

This is needed when host is known to not work properly in high speed
mode.

In linux, chipidea driver supports 'maximum-speed' device tree property.
When that is set to "full-speed", driver sets PFSC bit in PORTSC
register, which disallows use of high speed mode.

This patch implements same support for barebox.

Important technical detail is that PFSC bit is cleared by port reset,
thus setting it has to be done in ehci->init() callback which is called
after ehci_reset().

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: fastboot: Add external command execution support ...

Custom projects may need vendor specific expansions to the fastboot
command execution. Allow these to be implemented without messing in
the fastboot code directly.
We have a hook for all commands and also one for the "flash" command.
Each hook can decide if the generic command parser is executed
afterwards (return value FASTBOOT_CMD_FALLTHROUGH) or if the generic
parser shall be skipped (return value 0 or negative error code).

This allows board code to implement vendor specific "oem" commands
or to handle the downloaded image in a special way (i.e. do signature
checks on them)

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usbgadget: fastboot: Allow to automatically export the bbu handlers ...

We have a list of registered handlers which take a barebox update. Do
the next step and allow to automatically export them via fastboot so
that barebox can be updated via fastboot without manually exporting
the partition. Since this may not be desirable in all cases this
behaviour is configurable.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: properly release f_multi_opts ...

The usbgadget commands uses statically allocated f_multi_opts and passes
this to usb_multi_register(). These f_multi_opts are of course no
longer valid when we leave the usbgadget command. Luckily we do not use
the data after we left the usbgadget command, so this never has been a
problem. However, f_multi_opts has some allocated members which we can
not free anymore on gadget unregistration because we no longer have the
pointer to them.

Fix this by adding a release function to struct f_multi_opts. This way
we can allocate all memory dynamically and properly free it when not
used anymore.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: imx: Make usb-misc multi instance safe ...

i.MX7 has two usbmisc devices, so we cannot use global instance
variables anymore. Create a driver private data struct for it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: ehci: forward phy given in registration data to host ...

Allow to pass a phy in the registration data and forward it to
the usb_host structure.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: Add usb phy to usb host ...

Add a struct usb_phy * member to struct usb_host. Also, call
usb_phy_notify_connect() / usb_phy_notify_disconnect() when there
are connection changes on the root hub.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Introduce include/linux/spinlock.h ...

Move spinlock related definitions to its original place.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: core: return -EAGAIN on usb_* functions reentrance ...

Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/usb'

chipidea-imx: allow phymode configuration in pdata ...

it's currently only handled through DT and for i.MX25 OTG port (at least),
we need to configure portsc to get host mode working but it actually fails
as ci->phymode is 0 which is USBPHY_INTERFACE_MODE_UNKNOWN

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>