plat: marvell: armada: a8k: check CCU window state before loading MSS BL2 ...

Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL2 stage the CCU Win-2 points to DRAM. If additional mapping is
added to MSS BL2 stage initialization, the DDR entry will be destroyed
and lead to the system hang.

Change-Id: I215e83508acc37d54dab6954d791b9a74cc883ca
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

drivers: marvell: align and extend llc macros ...

Make all LLC-related macros to start with the same prefix
Add more LLC control registers definitions
This patch is a preparation step for LLC SRAM support

Change-Id: I0a4f0fc83e8ef35be93dd239a85f2a9f88d1ab19
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

plat: marvell: a8k: move address config of cp1/2 to BL2 ...

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done after access to each CP is provided.
Moving the proper configuration from BL31 to BL2 solves it.

Change-Id: I44cf88dfd4ebf09130544332bfdd3d16ef2674ea
Signed-off-by: Ben Peled <bpeled@marvell.com>

plat: marvell: armada: re-enable BL32_BASE definition ...

As a preparation to support proper loading the OPTEE OS image,
enable the BL32 specific defines in case the SPD is used.

On the occasion move two BL32-related macros to marvell_def.h
and fix BL32_LIMIT definition.

Change-Id: Id4e2d81833bc1895650cca8b0fc0bfc341cf77f3
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer ...

The phy porting layer uses defaults defined in
"phy-default-porting-layer.h" when board specific file
"phy-porting-layer.h" is not found. Because of the regression the board
specific directory was not included, therefore all boards used default
parameters.

Change-Id: I66e5e6eb8a39cca5aeeb4de6dab2ceddc39c1e31
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

plat: marvell: armada: configure amb for all CPs ...

Before this patch the configuration took place only for CP0 and CP1, but
since new platforms can contains up to 3 CPs update is required.

Change-Id: Iebd50bbe7b9772063e2c4efb3a7ecbfd593e950d
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs ...

The Marvell Armada 37xx SoCs-based platforms contain a bit
awkward directory structure because the currently only one
supported PLAT and PLAT_FAMILY are the same. Modify the latter
to 'a3k' in order to improve it and keep plat/marvell/armada
tree more consistent:

plat/marvell/
├── armada
│   ├── a3k
│   │   ├── a3700

[...]

│   ├── a8k
│   │   ├── a70x0

[...]

Change-Id: I693a6ef88e6ce49a326a3328875c90bbc186066a
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration ...

* changes:
  ddr: a80x0: add DDR 32-bit ECC mode support
  ble: ap807: improve PLL configuration sequence
  ble: ap807: clean-up PLL configuration sequence
  ddr: a80x0: add DDR 32-bit mode support
  plat: marvell: mci: perform mci link tuning for all mci interfaces
  plat: marvell: mci: use more meaningful name for mci link tuning
  plat: marvell: a8k: remove wrong or unnecessary comments
  plat: marvell: ap807: enable snoop filter for ap807
  plat: marvell: ap807: update configuration space of each CP
  plat: marvell: ap807: use correct address for MCIx4 register
  plat: marvell: add support for PLL 2.2GHz mode
  plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
  marvell: armada: add extra level in marvell platform hierarchy

plat/arm: Fix load address of TB_FW_CONFIG ...

Load address of tb_fw_config is incorrectly mentioned
in below device trees:
1. rdn1edge_fw_config.dts
2. tc0_fw_config.dts

Till now, tb_fw_config load-address is not being retrieved from
device tree and hence never exeprienced any issue for tc0 and
rdn1edge platform.

For tc0 and rdn1edge platform, Load-address of tb_fw_config should
be the SRAM base address + 0x300 (size of fw_config device tree)
Hence updated these platform's fw_config.dts accordingly to reflect
this load address change.

Change-Id: I2ef8b05d49be10767db31384329f516df11ca817
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Tegra194: ras: verbose prints for SErrors ...

This patch provides verbose prints for RAS SErrors handled by the
firmware, for improved debugging.

Change-Id: Iaad8d183054d884f606dc4621da2cc6b2375bcf9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra194: SiP: clear RAS corrected error records ...

This patch introduces a function ID to clear all the RAS error
records for corrected errors.

Per latest requirement, ARM RAS corrected errors will be reported to
lower ELs via interrupts and cleared via SMC. This patch provides
required function to clear RAS error status.

This patch also sets up all required RAS Corrected errors in order to
route RAS corrected errors to lower ELs.

Change-Id: I554ba1d0797b736835aa27824782703682c91e51
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: David Pu <dpu@nvidia.com>

Tegra194: add RAS exception handling ...

This patch adds all Tegra194 RAS nodes definitions and support to
handle all uncorrectable RAS errors.

Change-Id: I109b5a8dbca91d92752dc282c4ca30f273c475f9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Merge "rockchip: rk3368: fix PLAT_RK_CLST_TO_CPUID_SHIFT" into integration

Merge "GICv3: GIC-600: Detect GIC-600 at runtime" into integration

rockchip: rk3368: fix PLAT_RK_CLST_TO_CPUID_SHIFT ...

The RK3368 has two clusters of 4 cores and it's cluster id starts at
bit 8 of the MPIDR.  To convert from the cluster id (0 or 1) to the
lowest CPU-ID in the respective cluster, we thus need to shift by 6
(i.e. shift by 8 to extract the cluster-id and multiply by 4).

This change is required to ensure the PSCI support can index the
per-cpu entry-address array correctly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Change-Id: I64a76038f090a85a47067f09f750e96e3946e756

Merge changes from topic "sp_secure_boot" into integration ...

* changes:
  dualroot: add chain of trust for secure partitions
  sptool: append cert_tool arguments.
  cert_create: add SiP owned secure partitions support

plat/fvp: Add support for dynamic description of secure interrupts ...

Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.

Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

GICv3: GIC-600: Detect GIC-600 at runtime ...

The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

dualroot: add chain of trust for secure partitions ...

A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.

To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.

The CoT for secure partition look like below.
+------------------+       +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key       |
+------------------+       | Certificate       |
                           | (Auth Image)      |
                          /+-------------------+
                         /                   |
                        /                    |
                       /                     |
                      /                      |
                     L                       v
+------------------+       +-------------------+
| Trusted World    |------>| SiP owned SPs     |
| Public Key       |       | Content Cert      |
+------------------+       | (Auth Image)      |
                        /   +-------------------+
                       /                      |
                      /                      v|
+------------------+ L     +-------------------+
| SP_PKG1 Hash     |------>| SP_PKG1           |
|                  |       | (Data Image)      |
+------------------+       +-------------------+
        .                           .
        .                           .
        .                           .
+------------------+       +-------------------+
| SP_PKG8 Hash     |------>| SP_PKG8           |
|                  |       | (Data Image)      |
+------------------+       +-------------------+

Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f

Merge "plat/arm: do not include export header directly" into integration

Merge "rockchip: increase FDT buffer size" into integration

plat: intel: Additional instruction required to enable global timer ...

There are additional instruction needed to enable the global timer.
This fixes the global timer initialization

Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Idaf2d23359aacc417e2b7d8cdf1688b5cd17ca98

plat: intel: Fix CCU initialization for Agilex ...

The CCU initialization loop uses the wrong units, this fixes that. This
also fixes snoop filter register set bits should be used instead of
overwriting the register

Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Ia15eeeae5569b00ad84120182170d353ee221b31

rockchip: increase FDT buffer size ...

The size of buffer currently used to store the FDT passed from U-Boot as
a platform parameter is not large enough to store some RK3399 device
trees. The largest RK3399 device tree currently in U-Boot (for the
Pinebook Pro) is about 70KB in size when passed to TF-A, so increase the
buffer size to 128K which gives some headroom for possibly larger FDTs
in future.

Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Change-Id: I414caf20683cd47c02ee470dfa988544f3809919

plat: intel: Add FPGAINTF configuration to when configuring pinmux ...

FPGAINTF wasn't enabled when configuring pinmux. This fixes the issue.

Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: I5a6aacd504901b8f7327b2f4854b8a77d0c37019

plat: intel: set DRVSEL and SMPLSEL for DWMMC ...

DRVSEL and SMPLSEL needs to be set so that it can properly go into full
speed mode. This needs to be done in EL3 as the registers are secured.

Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Ia2f348e7742ff7b76da74d392ef1ce71e2f41677

plat: intel: Fix clock configuration bugs ...

This fixes a few issues on the Agilex clock configuration:
- Set clock manager into boot mode before configuring clock
- Fix wrong divisor used when calculating vcocalib
- PLL sync configuration should be read and then written
- Wait PLL lock after PLL sync configuration is done
- Clear interrupt bits instead of set interrupt bits after configuration

Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: I54c1dc5fe9b102e3bbc1237a92d8471173b8af70

plat/arm: do not include export header directly ...

As per "include/export/README", TF-A code should never include export
headers directly. Instead, it should include a wrapper header that
ensures the export header is included in the right manner.

"tbbr_img_def_exp.h" is directly included in TF-A code, this patch
replaces it with its  wrapper header "tbbr_img_def.h".

Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I31c1a42e6a7bcac4c396bb17e8548567ecd8147d

ddr: a80x0: add DDR 32-bit ECC mode support ...

Change a topology map from internal database
to SPD based for 32bit bus width mode

Change-Id: I803166893ddc2fd916fc8a1c27fffd34b6ec0c72
Signed-off-by: Alex Leibovich <alexl@marvell.com>

ble: ap807: clean-up PLL configuration sequence ...

Remove pll powerdown from pll configuration sequence to improve
stability. Remove redundant cases, which no longer exist.
Also get rid of irrelevant definition of CPU_2200_DDR_1200_RCLK_1200,
which is not used by 806/807.

Change-Id: If911e7dee003dfb9a42fafd7ffe34662f026fd23
Signed-off-by: Alex Leibovich <alexl@marvell.com>