Merge branch 'for-next/rtc'

Merge branch 'for-next/pstore'

Merge branch 'for-next/net'

Merge branch 'for-next/mtd'

Merge branch 'for-next/misc'

Merge branch 'for-next/imx'

Merge branch 'for-next/gcc5'

Merge branch 'for-next/dts'

Merge branch 'for-next/arm'

Release v2016.01.0 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Fix exception table setup in MMU-less mode ...

Add code necessary for correct initialization of exception vector
table when MMU is disabled.

Note: Only ARMv7 support is implemented

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: mmu: Add VBAR setup ...

Add code to make sure that normal vector exception table, when it is
used due to unavailability of the high vector table, was not re-mapped
from 0x0 via VBAR by someone else before us.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: asm: Add convenience fucntions to access VBAR ...

Add two functions to get/set VBAR register.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

reset: fix non GPIO reset ...

The reset controller structure is zero initialized in the OF
reset case, but as 0 is also a valid GPIO number the current
code tries to assert/deassert the GPIO instead of calling into
the reset controller device.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: chipidea-imx: check return value of regulator_get() ...

The VBUS regulator is optional for the chipidea-imx glue, so it must
be checked if regulator_get provided a valid regulator handle before
trying to enable the regulator.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

PCI: imx6: properly shut down core when leaving barebox ...

As the i.MX6 PCIe core doesn't have a software reachable reset
wired up, it's hard for any driver to get the core into a known
good state.

To make it easier for whatever software follows barebox, bring
back the core into a safe state before leaving barebox.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX6: pci: Avoid aborts when asserting PCIe reset ...

When booting Barebox in the HW environment where PCIe core has been
used but not properly shut down, writing to PCIE_PL_PFLR in
imx6_pcie_assert_core_reset would cause data abort exception.

The problem can be easily reproduced on a i.MX6 based board with PCIe
slot populated with some device by doing:

> bootm -f -e 0x1050 <your board's>.img

Ignoring this exception seem to allow PCIe core to successfully
initialize and enumerate devices properly. This is also how Linux
Kernel version of the driver handles this situation -- it installs
dummy no-op abort handler at the beginning of device's probing.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX6: pci: Reconcile imx6_pcie_start_link with the kernel code ...

Reconcile imx6_pcie_start_link with almost identical
imx6_pcie_establish_link from analogous Linux kernel driver. This
change is purely cosmetical, but refactoring the code this way
simplifies implementation comparison.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX6: pci: Replace magic number with a named constant ...

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of_path: Drop possible further extensions of device-path property ...

Originally it was intended to further extend the multi string property
device-path further with more elements, like for example a filename. It
turned out though that this is too complex and instead of further
extending the property we should instead create additional properties,
so this mechanism is removed with this patch to make the code simpler.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

fs: automount: Make automountpoints persistent ...

Do not remove the automountpoints when they are mounted. This way
they can be reused when they have been unmounted.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

readline: Fix potential buffer overflow in command history ...

Cursor up copies the last line into the buffer without checking if it
fits into the current buffer. Fix this using safe_strncpy.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

readline: Fix potential buffer overflow ...

cread_add_char doesn't take the trailing '\0' into account, so adding
it at the end of readline can overflow the buffer.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

OF: Fix fixups to fix Linux DT instead of Barebox DT ...

OF fixups cm_cogent_fixup() and hb_fixup() are supposed to modify the
Linux device tree.  And they did originally, but commit
e520a8c changed them to use
for_each_compatible_node(), which iterates through the Barebox DT.
Use new for_each_compatible_node_from() to specify the Linux DT root
as the start point.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of: Add of_property_for_each_phandle() iterator ...

This is like of_property_for_each_{string,u32} but loops over a list
of phandles instead of strings or ints.

Returns the node the handle points to as that's generally more useful
than the handle value itself.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of: Add for_each_compatible_node_from iterator ...

The existing iterator for_each_compatible_node() searches for each
compatible node starting from the root of the loaded device tree.
This means it only works on the barebox device tree and not the tree
to be passed to the Linux kernel, which is what an of_fixup would
probably want to use.

This adds for_each_compatible_node_from(), which takes an additional
parameter of a root to search from.  This could be the device tree to
be used for the kernel.  It could also be used to search just a
subtree.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

socfpga: Find partition with environment via device tree ...

socfpga would load the environment from a file named "barebox.env"
located on the device "/dev/mmc0.1".  Both those names are hard-coded
in the socfpga code and can't be changed.

Barebox supports selecting the location of the environment using a
"barebox,environment" node in device tree's "chosen" node.  And
recently supports specifying that the env should come from a file on
this device.

Change socfpga to use this mechanism by adding the appropriate device
node.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

environment: Support env from file in a file-system via device tree ...

Current barebox,environment node only allows specifying a raw device or
partition to load an environment from.  Some boards, like OMAP and
SoCFPGA, instead want to use a file located in a FAT filesystem.
Extend the device tree bindings with a new property 'file-path' that
will trigger this behavior.

This allows any board using this driver to get the env from a file or
from a raw device, instead of each machine type being either raw
device only or file only.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

partition: Create links with partition names ...

When a partition has a name create a link to the original partition
rather than registering a second cdev.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

devfs: Add symlink support ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>