Merge branch 'for-next/reset-source'

Merge branch 'for-next/randconfig'

Merge branch 'for-next/pcm038'

Merge branch 'for-next/onfi'

Merge branch 'for-next/omap'

Merge branch 'for-next/mkublheader'

Merge branch 'for-next/misc'

Merge branch 'for-next/mips'

Merge branch 'for-next/m25p80'

Merge branch 'for-next/imx-misc'

Merge branch 'for-next/imx-keypad'

Merge branch 'for-next/i2c'

Merge branch 'for-next/friendlyarm'

Merge branch 'for-next/depend'

Merge branch 'for-next/defenv-2'

Merge branch 'for-next/compressed-prepare'

Merge branch 'for-next/cfa-10036'

Release v2012.08.0 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mem md: make md -s /dev/something work again ...

Since

|commit d22b85a
|Author: Sascha Hauer <s.hauer@pengutronix.de>
|Date:   Wed Jul 4 23:41:13 2012 +0200
|
|    mem md: bail out without arguments
|
|    Without arguments the 'md' command defaults to show address 0 which
|    likely results in a NULL pointer exception, so only three keystrokes
|    are necessary to crash barebox. Show usage instead if 'md' is invoked
|    without arguments, so that it at least requires an address to be given
|    to crash barebox. This increases the stability of barebox by 66%. Hurray!

barebox does not crash any longer when a plain 'md' without additional arguments
is exectuted. However, doing a 'md -s /dev/nor0' was a standard usecase which now
does not work anymore.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nor m25p80: implement fast read ...

The fast read command is needed for spi speeds > 25MHz, so use it for
higher speeds.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nor m25p80: optimize erase ...

The driver currently erases blocks in 4kb chunks if 4kb support is
available. This patch uses bigger blocks for suitable areas to speed
up erasing areas.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nor m25p80: align start and end to erase blocks ...

The erase command normally makes sure that the selected area is erased,
therefore align the parameters to eraseblock boundaries.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nor m25p80: refactor chip erase ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nor m25p80: remove unused variables ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nor m25p80: remove progression bar ...

Drivers should not print a progression bar.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i2c: add platform_data for i2c_board_info ...

Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

imx35: mmc clock has 6 bit divider, not 3_3 ...

Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

decompress_unlzo: define decompress_unlzo as decompress ...

so we can use decompress in the decompressor
this will simplify multi decompress support

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

kbuild: Init all relevant variables used in kbuild files ...

import from linux 3.5-rc5

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

MIPS: add initial exceptions handling ...

Checking exception handling:

    $ make qemu-malta_defconfig
    $ make

    ...

    $ qemu-system-mips -nodefaults -M malta -m 256 \
       -nographic -serial stdio -bios ./barebox.bin

    ...

    barebox:/ md -l 0x03

    Ooops, address error on load or ifetch!
    EPC = 0xa082783c
    CP0_STATUS = 0x00000006
    CP0_CAUSE = 0x00000410
    CP0_CONFIG = 0x80008482

    ### ERROR ### Please RESET the board ###

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>