crypto: add CRC32 digest ...

CRC32 digest can be used to check CRC32 hashes in FIT images etc.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of: base: Match simple-mfd devices ...

Some simple-buses are now considered to be simple-mfd devices. Match
them aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

rtc: ds1307: Add ds1308 to driver's ID list ...

As far as the driver is concerned, it's the same as a 1338.  It's too
bad the i2c drivers can't make use of OF compatible properties with a
list of compatible devices.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: phy: micrel: KSZ9081/KSZ8091: Disable broadcast mode ...

KSZ9081 only supports two phy ids 0x0 and 0x3. 0x0 is also
used as broadcast address. Disable broadcast, so that id 0x0
can be used as unique address on a shared bus.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

partitions: dos: add partuuid string for logical partitions ...

Commit bc31d85c6e23 ("cdev: Add partuuid string to struct cdev") added
partuuid strings for dos partitions but only for the (up to) four
primary partitions. Do the same for the logical partitions. Their
numbers start at 5 independently of the number of available primary
partitions.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/ubiformat'

Merge branch 'for-next/pci'

Merge branch 'for-next/mtd'

Merge branch 'for-next/misc'

Merge branch 'for-next/include-pdata'

Merge branch 'for-next/include-cleanup'

Merge branch 'for-next/imx6-phytec'

Merge branch 'for-next/imx'

Merge branch 'for-next/bootm'

Merge branch 'for-next/arm'

Release v2016.05.0 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: imx-esdhc: implement reset quirks for i.MX6 DualLite/Solo ...

First of all the reset values of MMC interfaces are differently between
Quad and DualLite/Solo SoM.

                Register VEND_SPEC2(0xC8)
    Quad:       0x0
    DualLite:   0x00000006
    default:    0x00000006    (from i.MX6 Reference Manual)

Furthermore the ROM Code of Quad and DualLite uses the MMC interfaces
differently when it loads the bootloader from that device:

                Register DLL_CTRL(0x60)  Bit 25 FBCLK_SEL (0x48)
    Quad:       0x0                      0
    DualLite:   0x01000021               1

Since the linux kernel and barebox driver doesn't reset all registers,
the MMC interface is in an inconsistent state, which leads to boot
failures for some eMMC devices on the i.MX6 DualLite SoM. The errors
look like:

    mmcblk3: error -110 sending stop command, original cmd response 0x900, card status 0x400900
    mmcblk3: error -84 transferring data, sector 24578, nr 2, cmd response 0x900, card status 0x0
    mmcblk3: retrying using single block read
    mmcblk3: error -84 transferring data, sector 24578, nr 2, cmd response 0x900, card status 0x0
    blk_update_request: I/O error, dev mmcblk3, sector 24578

It's sufficient to reset register DLL_CTRL and bit FBCLK_SEL. Register
VEND_SPEC2 has no effect.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: phy: Add fixed link support ...

Some network devices, especially when connected to a switch, are
connected via a fixed link. This patch adds support for a fixed phy
configured through device tree.
TODO: Add support for the "speed" and "full-duplex" properties.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Wjatscheslaw Stoljarski <wjatscheslaw.stoljarski@kiwigrid.com>

ARM: phytec-som-imx6: add automount for first partition on eMMC ...

For the phyCORE-i.MX6 add an automount command for the first partition
on the eMMC device.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

blspec: push appendroot handling to bootm ...

The bootm code now can handle the adding of the root= option itself,
so drop the code and let bootm do it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

bootm: Optionally add a root= option to Kernel command line ...

It becomes a common case that the Kernel is loaded from the filesystem
which later becomes the rootfs. This adds a possibility to let bootm
automatically append the root= option to the kernel command line. This
is done when global.bootm.appendroot is true.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

parameter: Use strtobool ...

Use strtobool to convert the input string to a boolean type.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

PCI: imx6: Add DT bindings to configure PHY Tx driver settings ...

The settings in GPR8 are dependent upon the particular layout of the
hardware platform.  As such, they should be configurable via the device
tree.

Look up PHY Tx driver settings from the device tree.  Fall back to the
original hard-coded values if they are not specified in the device tree.

[Andrey Smirnov: port to Barebox codebase]

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

PCI: imx6: Remove broken Gen2 workaround ...

Remove the remnants of the workaround for erratum ERR005184 which was never
completely implemented.  The checks alone don't carry any value as we don't
act properly on the result.

A workaround should be added to the lane speed change in establish_link
later.

[Andrey Smirnov: port to Barebox codebase]

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

PCI: imx6: Move PHY reset into imx6_pcie_establish_link() ...

This adds the PHY reset into a common error path of
imx6_pcie_establish_link(), deduplicating some of the debug prints.  Also
reduce the severity of the "no-link" message in the one place where it is
expected to be hit when no peripheral is attached.

[Andrey Smirnov: port to Barebox codebase]

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phytec-som-imx6: add NOR for phycore-imx6 emmc ...

Enable NOR for phyCORE-i.MX6 DualLite and Quad eMMC variants.

Furthermore add an extra 'status = "disabled"' in the flash node.  It
has no functional effect, because the SPI bus node 'ecspi1' is disabled,
too.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phytec-som-imx6: adapt main update handler for eMMC ...

Some phyCORE-i.MX6 variants have eMMC instead of a NAND chip. Provide an
update_handler for them.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phytec-som-imx6: rename environment folder ...

The extra environment folder for the phyCORE-i.MX6 had the suffix
'-mira'. That's the name of a baseboard. Since the bootloader is generic
for all baseboards, use a generic suffix for the environment folder.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phytec-som-imx6: update RAM calibration for phycore-imx6dl ...

Update RAM calibration values in the flashheader file for phyCORE-i.MX6
DualLite/Solo. These are verified and tested in the climatic chamber for
commercial, extended commercial, industrial and automotive i.MX6
variants.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phytec-som-imx6: add phyCORE-i.MX6 DualLite ...

Add Phytec phyCORE-i.MX6 SOM.
  Support:
   - imx6dl-phytec-phycore-som-emmc:
      - 1GB RAM on 1 Bank with 64Bit
      - 10/100MBit Ethernet
      - SPI NOR
      - eMMC
      - SD
      - UART

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>