devices: add detect mechanism ...

We often encounter the situation where slow devices should not be
probed during startup since probing is slow and maybe unnecessary
for unused devices. With MMC we have the 'probe' device parameter,
for ata we have the same, for USB we have the 'usb' command. Overall
this is not very consistent.
With MMC there is the additional problem that the probe parameter
is attached to the logical device when we often have the information
which physical device we want to probe.
This patch adds a 'detect' callback for devices and adds a command
to detect devices and to list the devices which are actually detecable.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

twl6030: Set WR_S for VMMC ...

After Reset VMMC goes to default VSEL. This is not a clean power cycle for
some SD cards.
Set flag WR_S for VMMC to avoid going to default VSEL.

Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: imx-esdhc: allow to specify devicename via OF alias ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of: Add of_alias_get function ...

This is used to retrieve the name of the alias for a given
devicenode.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: set name of mci device to same name as the filename ...

We already have the possibility to register a mci with a certain
filename to get persistent names. However, the device needed to
find the probe parameter still has the name 'mcix'. This patch
changes this by registering the mci device with the same name
as the filename.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: embed mci device into struct mci ...

To safe a separate allocation and to make the code simpler.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: make mci device a pure device ...

No need to match and probe the device if all that we want is a logical
deivice for the mci.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

driver: Attach info callback to device, not to driver ...

Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: Add support for MMC boot partitions ...

Some MMC cards support boot partitions. These are special regions
on the MMC card intended to put a bootloader on.

This patch adds support for these partitions, they are accessible
as /dev/diskx.boot[0|1].

Additionally the partitions can be configured bootable using a
device parameter. This can be used to mark the user area or one
of the boot partitions as bootable.

Since this feature is mostly seen on eMMC cards it is made optional
to lower the size impact for boards which do not have eMMC.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci i.MX esdhc: Fix clock divider calculation ...

This updates the i.MX esdhc divider settings to FSLs U-Boot.
Current timings work fine for SD cards, but not for eMMC.
Although the calculation is fine according to the datasheet and reading from
eMMC works, writing is broken. Atleast on i.MX53/tqma53.
With this patch the result is the same, but uses different divider values to
achieve it.

While at it, replace the udelay with a busy-loop.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

MCI: Sort Makefile entries ...

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: OMAP MCI: Move TWL6030 power initialization into OMAP directory ...

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Added sd driver for bcm2835 (Raspberry PI) ...

Replaced defines according to sdhci.h

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: imx-esdhc: factor out common sdhci registers ...

This gives the SDHCI specific registers a common name and moves
them to a separate file for use by other SDHCI like drivers.

The SDHCI spec has some 16bit and 8bit registers. The i.MX accesses
these as 32bit registers. These register defines now are named after
the SDHCI registers they combine into one, for example:

SDHCI_HOST_CONTROL__POWER_CONTROL__BLOCK_GAP_CONTROL

is the 32bit version of the SDHCI registers HOST_CONTROL, POWER_CONTROL
and BLOCK_GAP_CONTROL.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

param: Add helpers to provide an enum parameter ...

We recently gained helper functions for different types of
device parameters. One thing missing was a helper for an
enum type parameter. This patch adds this.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

param: Add info function ...

Some parameters may wish to provide some information about their
meaning or possible values. Provide an info callback for parameters.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: invalidate data caches during early init ...

Some SoCs come up with invalid entries in the data cache. This can
lead to memory corruption when we enable them later, so invalidate
the caches early.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>

ARM v7: added v7_mmu_cache_invalidate() ...

At least the iMX6 boot rom seems to jump into barebox with a non
invalidated d-cache which causes data corruption when
v7_mmu_cache_flush() executed by arm_early_mmu_cache_flush() overrides
stack or other valid data.

That's why the cache must be invalided for this processors explicitly
(e.g. in barebox_arm_reset_vector()).  Operation differs from flush only
in one instruction so that patch modifies the existing
v7_mmu_cache_flush() function slightly by adding an optional argument.

Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM v7: v7_mmu_cache_flush(): do not restore r0-r3 (minor optimization) ...

Registers 'r0' till 'r3' are scratch registers and do not need to be
restored.

Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: properly init alignment trap bit ...

On ARMv7 the intention is to disable the alignment trap to be able to
use hardware assisted unaligned load/stores. Fix the init to do the
right thing.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

defaultenv-2: Fix settings entry ...

There is no "settings-entries-edit" command. This results in a recursive call
to the settings menu. Use the missing "boot-entries-edit" command instead.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: fix the memset fix ...

From Kernel commit 418df63a ARM: 7670/1: fix the memset fix

| Commit 455bd4c430b0 ("ARM: 7668/1: fix memset-related crashes caused by
| recent GCC (4.7.2) optimizations") attempted to fix a compliance issue
| with the memset return value.  However the memset itself became broken
| by that patch for misaligned pointers.
|
| This fixes the above by branching over the entry code from the
| misaligned fixup code to avoid reloading the original pointer.
|
| Also, because the function entry alignment is wrong in the Thumb mode
| compilation, that fixup code is moved to the end.
|
| While at it, the entry instructions are slightly reworked to help dual
| issue pipelines.
|
| Signed-off-by: Nicolas Pitre <nico@linaro.org>
| Tested-by: Alexander Holler <holler@ahsoftware.de>
| Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

fdt: Fix dt memreserve entry ...

The fdt reserve map needs address/size values, not address/end values
like accidently done for generating the reserve entry for the dt.

Reported-by: Jürgen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM v7: fix mmu-off operation ...

Although conclusions in 50d1b2d "ARM
v7: Fix register corruption in v7_mmu_cache_off" are correct, the
implemented fix is not complete because the following failure can
happen:

1. d-cache contains the cache line around 'sp'

2. v7_mmu_cache_off() disables cache

3. early v7_mmu_cache_flush() pushes 'lr' on uncached stack

4. v7_mmu_cache_flush() flushes d-cache and can override stack written
   by step 3.

5. v7_mmu_cache_flush() pops 'lr' out of cache and jumps to it which
   might be random data now.

Patch avoids step 3 which is easy because 'lr' is never modified by the
function.  By using the 'r12' scratch register instead of 'r10', the
whole initial 'push' can be avoided.

Patch moves also the 'DMB' operation so that it is executed after data
has been pushed on stack.

Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nand_base: sync flash detection functions with linux 3.9's code ...

this fix the problems introduced when detecting non ONFI flashes in
commit 4c2bdc8
"nand_base: detect more ONFI flash"

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'pu/dhcp'

ARM: ccmx51: Another fix SDRAM size detection ...

For CCMX51-boards now we do not use ESDCTL, but actual command for
adding memory is missing. This patch fix this issue.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dhcp: Fix tftp servername handling ...

When the dhcp code discovered the tftp-server-name option it immediately
tries to resolve the name. This can't succeed since the we are somewhere
in the dhcp processing and the nameserver may not even be known.

Fix this by resolving the name when dhcp is completed. While at it, do
this in a way that net_set_serverip is only called when resolv() returns
something useful. Otherwise we may end up overwriting a previously
configured serverip which came from the bootp bp_siaddr field.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dhcp: Fix return value on ctrl-c ...

the dhcp command will return with 0 when ctrl-c is pressed. Fix this to
-EINTR instead.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

gpio: fix typos ...

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>