Merge branch 'for-next/dts'

Merge branch 'for-next/defconfig-update'

Merge branch 'for-next/arm'

Release v2016.11.0 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of: of_find_path: Add support for new partition binding ...

The partitions now may be in a subnode of the actual device node.
Eventually go another step up in the hierarchy if required.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of: partitions: Support new binding ...

The new binding recommends to put the partitions into a subnode
with compatible "fixed-partitions". Add support for this binding.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: spi-nor: add MX25U2033E ...

This chip can be found in 4th generation Kindle devices

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: nand: nand_mxs: Fix readtotal calculation ...

The calculation of readtotal must be bit alligend. If not the bch core
finds bit flips in every page, because readtotal is too small.
This bug was mostly introduced since commit "51061a9 mtd: nand: nand_mxs:
Add subpage read support".

Tested with:
nand: NAND device: Manufacturer ID: 0x01, Chip ID: 0xd3 (AMD/Spansion
S34ML08G2), 1024MiB, page size: 2048, OOB size: 128

nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron
MT29F4G08ABADAWP), 512MiB, page size: 2048, OOB size: 64

nand: NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND
1GiB 3,3V 8-bit), 1024MiB, page size: 2048, OOB size: 64

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: Make UBI detection more robust ...

When we want to detect if a mtd device contains an UBI image then
testing the first block is not enough since it can always happen that
UBI has just erased the block before the power failed during last boot.
Since UBI only ever erases one block at a time and directly writes the
ec header to it afterwards, it shouldn't be necessary to scan the whole
device for UBI data. Scan the first 64 blocks. The first non-empty block
then must contain UBI data, if instead we find foreign data we assume
that no UBI is on that mtd device.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nand: imx6: Changed default NAND clock ...

The Barebox recognized false bad erase blocks while booting from a
Spansion NAND (1). This error occurred due a to high clock. The
Kernel sets the default NAND clock to 22Mhz. So, to fix this error and
to be more identical with the Kernel, the Barebox should be too.

1: nand: NAND device: Manufacturer ID: 0x01, Chip ID: 0xd3 (AMD/Spansion
S34ML08G2), 1024MiB, page size: 2048, OOB size: 128

Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Tested-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Fix appended device tree when CONFIG_OFTREE is enabled ...

When CONFIG_OFTREE is enabled the appended device tree is unflattened
and put into data->of_root_node, but there it is never used again.
To actually use the appended device tree put it into data->oftree
instead.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

scripts imx-image: add DCD NOP command support ...

The DCD NOP command is available for all flash header v2 devices (i.MX28,
50, 53, 6 and 7).

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

state: fix state is not saved when string variable is changed ...

The dirty flag was not set properly.

Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: riotboard: fix barebox partition size ...

This was missed when updating all the partition sizes. The
environment partition has been moved to the correct location,
but the barebox partition size remained unchanged.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: e1000: fix i210 register remapping ...

Don't mask out the remapping flag before checking the register offset,
otherwise none of the switch statements will ever match.

Fixes: ff6a64d42ffc (e1000: Consolidate register offset fixups)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: dts: am33xx.dtsi: Add spi aliases ...

We need to add the spi aliases to set the bus number correct in
the driver.

Delete the spi1 alias again in the am33xx-strip.dtsi for MLO as
the node is deleted there also.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

dts: update to v4.9-rc2 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: Baltos: don't invoke baltos_read_eeprom in MLO ...

EEPROM information is needed in barebox.bin in order to setup MACs and
select appropriate DTB from kernel-fit.itb, so disable this initcall
in MLO.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: ubi: enable thread earlier ...

Since "57cebc4 mtd: ubi: Fix scrubbing during attach" we make sure
that the wear level worker does not start too early. However, now
there are cases when the worker starts too late. When a ubi image is
freshly written a volume may be autoresized. This has to be done
after the wear level worker is started because otherwise the initial
fastmap update will not be able to find any anchor PEBs.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: Baltos: setup MPU PLL to run at 600MHz ...

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

dts: update to v4.9-rc1 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: bootm: Fix free_mem calculation when initrd is given ...

When a initrd is given we calculate the next free memory position
as:
free_mem = PAGE_ALIGN(initrd_end);
This is wrong when initrd_end exactly falls on a page boundary.
In this case PAGE_ALIGN() does nothing and free_mem becomes
initrd_end and the following bootm_load_devicetree() and thus
booting fails with -ENOMEM.

Fix this by correctly advancing to the next free memory position.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX Freescale Sabrelite: Use correct device tree for dl variant ...

The i.MX6dl variant also uses the i.MX6q device tree which is wrong.
Use the correct one.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arch: refresh defconfigs ...

The defconfig files are long untouched and a
make xy_defconfig; make savedefconfig usually generates quite
a different looking file. Refresh them to make it easier to generate
patches against the configs using
make xy_defconfig; make menuconfig; make savedefconfig

This has been done with the following script.

for a in arch/*; do
	arch=$(basename $a)
	for c in $a/configs/*; do
		config=$(basename $c)

	export ARCH=$arch
	make $config && make savedefconfig && mv defconfig $c
	done
done

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

boot: add '-w' parameter to usage help text ...

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: ubi: Fix scrubbing during attach ...

ensure_wear_leveling() is called at the end of ubi_wl_init() and may
come to the decision to scrub some blocks. In the Kernel this is done
in a separate thread, but in barebox we do this synchronously. The
problem is that during ubi_wl_init() the EBA system is not yet
initialized (ubi_eba_init() is not yet called), so the wear level worker
hits a NULL pointer deref when the fastmap needs to be updated and
ubi_write_fastmap() accesses vol->eba_tbl.

Solve this by honoring the ubi->thread_enabled flag which is only set
to true when UBI is sufficiently initialized. This means we now can
have multiple works queued, so we can no longer simply do one work when
queued, but instead have to continue to do work until all work is done.
The best place to do so is a ubi_thread() function which behaves similar
to the Kernel function with the same name, but is called synchronously
in barebox. To make sure that the initially queued works are done, the
call to (no-op) wake_up_process() at the end of ubi_attach_mtd_dev()
is replaced with a call to ubi_thread().

While at it also honor the ubi->ro_mode flag to make sure we do not do
any wear leveling work on readonly UBI devices.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6: add support for Auvidea H100 ...

The Auvidea H100 is a baseboard for the SolidRun MicroSOM, which
provides HDMI IN/OUT capabilities.

Currently supported is only a combination of the H100 baseboard
with a i2eX MicroSOM.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: microsom: use imx6q_barebox_entry ...

Instead of hardcoding the different RAM sizes.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/usb'

Merge branch 'for-next/ubi'