mtd nand: allow partial page writes ...

The nand layer handles partial page writes just fine. If the start or
end of the data is not page aligned, the nand layer will copy the data
to a temporary page buffer.
Remove the check which disallows partial page writes since this is what
we want to do on barebox when for example an image is written to nand
which is not padded to page size.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Release v2012.12.0 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

at91: add_gpio_keys_device: fix missing conversion to DEVICE_ID_DYNAMIC ...

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

at91sam9260ek: fix BOARDINFO text ...

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX6: Add sata device ...

This also adds and enables the clocks needed for SATA.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX: Add i.MX51 PATA device support ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ata: Add i.MX PATA driver support ...

Straight forward driver, we only have to configure some additional
bits and then use the generic ide support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX6: save boot location ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX bbu internal: Add spi/i2c support ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX bbu: Add i.MX6 MMC handler ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX: Add Garz+Fricke Vincell Board support ...

This adds support for the Garz+Fricke Vincell board. This has
a i.MX53 Processor with 512MB of DDR3 RAM.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX esdctl: Use defines from exisiting header file ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX: add esdctl-v4 support ...

This adds support for initializing DDR3 RAMs on the i.MX53 type
SDRAM controller. The code automatically detects size/layout of
the connected RAM, detects the bus width and which chipselects are
populated.
While I believe this code is not 100% generic, it is far too
sophisticated to stay in a single board directory. I'm sure
other boards could make use of this aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX5: move pll setup defines to header file ...

The pll setup function is exported, so it makes sense to export
the convenience wrappers for specific frequencies aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX bbu: Allow to have no DCD ...

Some boards do not have a DCD table since they initialize everything
in code, so allow to skip it and leave the corresponding pointers
empty.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX bbu: Allow to overwrite app_dest ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX boards: use esdctl code to detect sdram size ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX: register esdctl controller device ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX: Add driver to get sdram base and size ...

The code initializing the SDRAM controller is not at the same
place where SDRAM is registered with barebox. To reduce the
risk of registering wrong SDRAM sizes this patch adds a
driver for the ESDCTL which reads back the configured SDRAM
size and registers the memory found with barebox.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX6 clk: remove gate_mask from pllv3 ...

Not needed as we will handle the additional gate bits as gate.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX6 pllv3: Do not use delay functions ...

We may be called very early, before the timer is available,
so don't use it here.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

clk: Add clk table based divider support ...

For easy support of table based dividers.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX6: rename PLLs according to datasheet ...

In recent reference manuals the plls were renumbered. PLL8 now is
PLL6 and vice versa. Change the code according to the reference
manual to avoid confusion.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM i.MX6: fix ethernet PLL rate ...

The ethernet PLL has a fixed frequency of 500MHz. What is adjustable
are additional dividers which we better describe separately.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: nand: mxs: reset BCH earlier, too, to avoid NAND startup problems ...

It could happen (1 out of 100 times) that NAND did not start up
correctly after warm rebooting, so barebox could not find its
environment or DMA timed out due to a stalled BCH. When resetting BCH
together with GPMI, the issue could not be observed anymore. We probably
need the consistent state already before sending commands to NAND.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci i.MX esdhc: turn error message into debug message ...

During card probe the mci core may send commands to the card
which the card doesn't understand. This is intended, so do not
print an error message here.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Define and use OMAP4 GPIO macros rather than magic constants. ...

Add and use meaningful macro names for OMAP4 GPIO addresses, and add a
comment to explain the 0x100 offset for OMAP4.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: phy: micrel: fix typo in driver name ...

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mach-omap/Kconfig: Some spelling fixes and indentation. ...

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Remove old, inaccurate "FileName:" cruft from ARM files ...

In addition, collapse adjacent comment blocks into one and remove
extraneous blank lines.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>