Release v2014.06.0 ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

serial: imx: Fix buggy transmissions when baudrate mismatches ...

Bit 7 of UCR3 is described in the i.MX reference manuals (with the exception
of i.MX1) as follows:

ADNIMP: Autobaud Detection Not Improved-. Disables new features of
	autobaud detection (See Baud Rate Automatic Detection
	Protocol, for more details).

	0 Autobaud detection new features selected
	1 Keep old autobaud detection mechanism

The "new features" mechanism occasionally causes the receiver to get out of sync
and continuously produces received characters of '0xff'.

In order to reproduce the problem:

$ cs0.baudrate=19200
- Change the terminal baudrate to 19200
- Type in the console and it should look good
- Change the terminal baudrate back to 115200
- Type 'b' in the console, then a stream of '0xff' is transmitted in loop

Setting the ADNIMP bit avoids the transmission of '0xff' in loop.

Also rename the bit definition as per the reference manual.

Tested on mx6q.

Based on a patch from Eric Nelson for U-boot.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

sama5d3x: fix AT91_SMC_CS offset stride ...

As stated in section 29.19.32 of SAMA5D3 Series datasheet, to move
from CS(n) to CS(n+1) the stride is 0x14 and not 0x10 as in the
other AT91 CPUs

Signed-off-by: Matteo Fortini <matteo.fortini@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: fec_imx: check return value of registration functions ...

We do not care about releasing the resources in the error
path, but at least check the return value of eth_register
and mdiobus_register.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: fec_imx: mask mii register reads correctly ...

mii registers are 16bit wide, so mask out the higher bits.
The higher bits confuse mii-tool.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: nand: mxs: Fix 2k nand with oob size of 224 bytes ...

The mxs nand driver has a calculation for the ecc strength.
This calculation was not used for some common nands and it
was assumed that 2k page nands always have a ecc strength
of 8. This is not true since there are devices with 224 bytes
of oob instread of 64 bytes. These allow for a greater ecc
strength. Since the kernel relies on the calculation and
we have to be consistent with the kernel use the calculcation
in barebox aswell and just remove our assumptions.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dm9k: only read on packet for each call to dm9k_eth_rx() ...

Some users such as fs/nfs.c just save the pointer to the packet in the
handler and process it after net_poll() returns. This break when more than
one packet is received using the same buffer.

Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM Samsung: fix booting from NAND with pbl ...

The ARM pbl is linked at (TEXT_BASE - SZ_2M). This conflicts with the temporary
stack used in s3c24x0_nand_boot. Moving the stack to (TEXT_BASE - SZ_2M) fixes
this problem. With this patch a compressed barebox with pbl can boot on
mini2440 from NAND.

Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: edmqmx6: disable menu framework ...

Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

syscon: fix prototype compile error ...

gcc 4.8.3 throws the following error

include/mfd/syscon.h: In function 'syscon_base_lookup_by_pdevname':
include/mfd/syscon.h:22:1: error: parameter name omitted
 static inline void __iomem *syscon_base_lookup_by_pdevname(const char *)

Fix it by adding the name to the function prototype.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: AM33xx: make bbu handler static inline ...

The static inline wrapper for am33xx_bbu_spi_nor_mlo_register_handler
lacked the 'static inline'. add it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: radxa-rock: set hostname after devicetree initialization ...

hostname_init() must be called after the devicetree root node has been
initialized, otherwise the check on board compatible always returns
false.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

driver/net: fix bus endianess access in ethoc.c ...

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

asm-generic: add IO memory accessors ...

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

common: fix macro WARN ...

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

drop CONFIG_PARTITION_NEED_MTD ...

With CONFIG_PARTITION_NEED_MTD enabled we use mtd rather than devfs
directly to create partitions on mtd devices. Since:

| commit b32cd8d
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date:   Wed Apr 9 15:49:32 2014 +0200
|
|     mtd: nand: bb: use mtd api directly
|
|     The devfs layer just adds an addition indirection between mtd
|     and the bb devices with no purpose. Drop it.
|
|     Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The bad block aware device creation doesn't work if this option
is disabled. With this we remove CONFIG_PARTITION_NEED_MTD and always
use mtd partitions on mtd devices.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

boot: iterate over directories in alphabetical order ...

When iterating over directories in order to find boot scripts do
this alphabetically to get a predictable order. This can be done
with glob() rather than readdir().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

boot: fix multiple boot sources ...

When there are multiple bootsources barebox should try booting them
until one succeeds. This is broken because we bail out of the iteration
loop with a goto. Remove the goto to fix this.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: dts: Add generated files to clean rule ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: dts: i.MX53: tqma53: Readd barebox specifics ...

Some of the barebox specific changes that were added in commit
e0316b4 got lost during the switch to use
upstream dtsi files in commit bb7cf71.

Especially the memory size is important since we have two different memory
sizes which have to be handled.

Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Fix the options and protocols used by the loadx command. ...

From 3cd9702 Mon Sep 17 00:00:00 2001
From: Owen Kirby <osk@exegin.com>
Date: Thu, 8 May 2014 13:27:11 -0700
Subject: [PATCH] Fix the options and protocols used by the loadx command.

It seems like the loadx command was improperly copy/pasted from the loady
implementation, and was trying to load files using the ymodem protocol. This
patch should fix the command so that it uses xmodem, implements the -t option
and outputs the correct baudrate being used.

Signed-off-by: Owen Kirby <osk@exegin.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

video: i.MX IPUv3: Print error as string ...

And add a missing newline.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

video: i.MX IPUv3: remove debug leftover ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX6: dts: edmqmx6: use new dts approach ...

Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: tegra30: ramp vdd_core to 1,2V ...

This isn't much different from the default 1,16V
and I haven't seen this make a difference on any
board, but it seems to be required for some T30 SKUs.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: tegra30: slow down CPU to 600 MHz ...

It's not safe to ramp up the CPU clock speed to
1,4 GHz on all T30 SKUs, as this may result in failure
to start the kernel properly. Start CPU at 600 MHz,
which is safe even for the slowest SKUs.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: dts: remove unused i.MX pinfunc header files ...

These are now taken from the upstream files.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phycard-imx6: fixup for barebox_arm_entry signature change ...

This board wasn't changed properly, as it was merged in the short
timeframe where the signature change waited to be applied. Change
it now to get rid of the compiler warning.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

stdlib.h: include missed types.h ...

We use 'u32' type in stdlib.h so we have to include types.h.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: bootm: fix default uImage placement ...

For small systems we would put the zImage at 32KiB after
the start of memory, and put the DT a bit after the uImage.
The kernel will always try to relocate itself and overwrite
the DT.

Try to be more clever at uImage placement to avoid
triggering the kernel relocation.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>